Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > X5 (E53) Forum
Arnott
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #171  
Old 05-13-2019, 09:28 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
So: how to calibrate your right side fuel sender if it's not reporting 1.4 ± 1L.

First get an ohm reading when you are confident you are at flood stage (left tank below 28L right staying the same).

The two terminals closest to the door jamb are the sender terminals.

When at flood stage you should see a value close to 37-39 Ω. If you get that reading but the test six right isn't showing 1.4ish the problem is elsewhere.

Mine was reading 22 Ω. Far far too low. The lowest reading on my sender was about 18 Ω and that registers 0.0L on the computer.

I took my fuel sender out and propped it into a vice;



Do it only exactly this way. It's the only place that holds it firmly and are and level.

Then I measured the distance from the floor to the bottom of the guide post:



It was almost exactly 118cm.

Then I measured the height from the floor to the center of the float when the sender reported the same Ω as reading in the car, it was almost exactly 2cm lower, VERY handy.

Then a few rounds of trial and error to get the Ω value of needed with the 2cm offset and about 1.5L at flood stage. (Bend the float arm a bit: more straight to get a higher Ω more bent to get a lower Ω. )



That was my bench reading. I think it ended up being closer to 39 Ω in the car but I'm very happy seeing 1.5L when driving now vs. 0.2L !



This is the fuel pump fuse. Very helpful for testing with test six before hooking everything back up!

I probably took the pump out and in about a dozen times today so I'm quite proficient at it now.

A couple tips:

don't try to feed the float in first when installing, hold it up vertically and let it fall down after it's in! Huge difference!

The seal MUST be on the TANK not the pump! It typically comes out with the pump but must be transferred back before reassembling.

Here's my biggest aha moment of the day: HOOK the float with a long piece or wire bent into a "J" at the bottom and lift it vertically for removal also! Wow did that make It go smoothly! It will catch on the edge just push it away from the edge with your finger.

Stall out the engine with the fuel fuse out to depressurize the fuel line. Then when removing the line, wrap with a paper towel about 10cc of fuel will be absorbed into the paper.

Safety dispose of fuel soaked paper with a lighter in a safe location (metal bin outside works well). If not windy the middle of a driveway also works well

I used my homemade bar for removing the big fuel tank "nut". I think photos are already in this thread.

That's the update for the right side sender. Left side sender resistor repair coming up.
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote

Sponsored Links

  #172  
Old 09-10-2021, 03:15 PM
Member
 
Join Date: Sep 2021
Location: Hungary
Posts: 1
Balavmw79 is on a distinguished road
Quote:
Originally Posted by andrewwynn View Post
after spending 20-30 hours searching every corner of the web to find out 'what the hell are all these parts' and why my x5 showed less than 1L of gas on the right tank and only went up to 1.1L after I made the recommended fix.

This is a detailed description, in most cases, the descriptions are verbatim or paraphrased from bmw technical manuals.
The right-hand side of the saddle-shaped fuel tank has a surge chamber with the electric fuel delivery pump.

The surge chamber guarantees correct fuel supply from the fuel delivery pump in all operating states of the vehicle.
the 'surge chamber' is a 'well' that contains about 5L of fuel. This well is clearly visible in the attached photo below.



The little 'foot' at the left of the photo (right side of tank) is literally where every drop of fuel your x5 consumes comes from.

Many bmw fuel tanks are 'saddle' type tanks but the x5 tank does not really qualify.

If you look closely at the photo, the x5 tank is closer to the shape of an old fashioned carpenter's folding ruler, that has been twisted 90 degrees about 40% up, or maybe better: a couple of 2x6 'lego' blocks attached at right angles on the corner, with a 1x2 on the bottom of the right side for the 'foot' or the 'well'.

This has a few implications:
  • there is not a well defined 'left' and 'right' side; the 'saddle' hump might be 2cm tall; you can see in some pictures, where the outlet of the siphon pumps are attached is slightly higher than the well (aka 'reserve tank').
  • once the fuel level gets lower than the flat area between the two sides, gas will no longer stay 'on the right side' other than exclusively in the reserve tank
  • this means, that since the right side sensor resides in the reserve tank, once your fuel level gets below about 33L, the right side sensor will read a relatively constant and very low amount (my wife's x5 reads 1.4L on a level ground, driving highway speeds)
  • the system is entirely dependent on the siphon 'jet pumps' (there are several other terms used interchangeably) at all times, since the car is always using 'the last 5L of gas).
Fuel is transferred from the left-hand side of the fuel tank to the surge chamber by the suction jet pump integrated in the tank expansion line. Both suction jet pumps are driven by the fuel return line. The pressure relief valve controls the pressure required for the suction jet pumps to operate.
Think of the pressure relief valve as a pressure regulator; if the return line is supplying too much pressure, or a jet gets plugged, the return fuel will vent into the surge chamber; sadly this won't get you more than 30-40 miles, but at least you will be able to consume the gas from the surge chamber and not have the system simply suck the reserve tank dry and put the gas on the left side of the tank.


The fuel is fed from the electric fuel delivery pump to the fuel rail via the fuel feed line and the fuel filter. Excess fuel is diverted back to the fuel tank by the pressure regulator fitted to the fuel rail and the fuel return line.
The fuel filter and pressure regulator are 'one in the same' on the x5. The fuel from the surge chamber (aka reserve tank) is pumped to the fuel filter/regulator and a constant stream of fuel comes back to the LEFT side of the tank.
The fuel level is measured by a lever-type sensor on each side of the fuel tank. The right-hand lever-type sensor is integrated into the fuel delivery unit. The left-hand lever-type sensor is located in the left-hand sensor unit. The actual fuel level in the tank is determined by linking the ohm values of the left and right-hand lever-type sensors
Since the right side sender float goes down into the reserve tank (which holds 5L) but it reads 1.4L when full on my wife's car when operating properly (meaning the surge tank is overflowing over 'the hump' back to the left side of the tank).

The low fuel light comes on when the calculated amount remaining is 8L or 10L of gas. There is some fuel (about a gallon) that remains when the computer measures 0.0L of gas. This will net you about 15-20 miles range past zero miles DTE.
Pressure regulator: 3.5 bar (S62: 5 bar)

Operating pressure of suction jet pumps: 1 - 1.3 bar
Ok that's a new tidbit of info; the suction pumps take 1 to 1.3bar of pressure to operate. I'm quite sure that info will help somebody out if they can only figure out how to connect a gauge; actually just a 't' adapter at the top of the left sender unit should work.

Here's a more photorealistic drawing of the fuel pump including the jet siphon pump. Note that the drawing indicates that the siphon pressure relief valve is actually connected to the electric pump but I'm not sure what variant of x5 does that. Not mine.



I've attached a diagram of what the tank more or less looks like from the back view; it's not really to scale, the 'well' on the right side is not nearly as big relative to the left body of the tank, but it's FAR closer to realty than any of the 'saddle type' tank diagrams i've almost universally seen.



(i'm not sure if the euro models or diesel especially may have a different tank, i can only go with the e53 gas like I have and that I exclusively see when searching for a part online).

I'm marked up a diagram of the fuel pumps including the jet suction pumps; i put red arrows to indicate the flow of fuel, the dashed red indicates the direction of fuel if the pressure gets to high in the return line and vents directly to the reserve tank.

When i repaired my wife's fuel supply system recently, I replaced the fuel pump first, afterwards I expected the fuel level in the right tank to rise since every single (of dozens) of articles online insisted that the jet pumps push the gas from the left side to the right side and that would make the left side drained and the right side hold the fuel.

This simply didn't happen and it's obvious why; the top of the reserve tank is flush with the 'plateau' between the left and right chamber so the 'right side' holds NO FUEL once the level of the gas gets below the plateau between the two sides.

That being said, i noticed that when my 'left side' got below about 27L of gas, the right side even with the new pump would't read even 1L of gas.. it stuck at 0.9L for 20 miles or so (where i maybe had 150miles to empty).

it was 0F outside when i needed to work on the truck so i 'bet on' it would not be fuel filter/regulator and would be something to do with the suction pump system.

I was correct; I found that the o-ring that seals the connection from the sender unit to the inlet of the suction jet pumps was totally dislodged from the groove; gas was obviously rushing around the seal and weakening the pressure.





From this knowledge I determined that the reason i could use some (maybe half) of the fuel from the left side was that the weight of the fuel aided the pressure at the inlet of the jet pump 'foot'; once the depth of the fuel was too shallow, it couldn't suck the fuel up and over, and i would run out of gas with maybe 15-20L of gas remaining in the tank.

I fixed the o-ring and started the car; the 0.9L of gas reading of the surge tank became 1.1L. At this time, i was still under the impression the sides were split and the value should grow on the right side, so i lifted the sender unit up on the left side while the car was running and imagine my surprise when gas was spraying out like a shower from the 'unlisted seal' that i've marked up on the diagram; where the hoses to the jet pump feet are attached; there was no o-ring or any type of seal and fuel was spraying out like a solid morning pee..



The left side of this pic (of the o-ring properly in place) also shows the mangled clip that holds the hoses to the jet pump feet

it took me a couple hours to re-engineer the part to get some o-rings in there and tie the thing back together because the 'only attach once' clips were not planning on holding very long.

Once i got it back together with o-ring seal at the 'unlisted' joint, started up and checked test 6; the value jumped from 1.1 to 1.4L. Time for a test drive.

Drove for about an hour and got the level down to below an eighth of a tank; got DTE to about half of the previous record.

I haven't had a chance to calibrate the fuel gauge by which I mean, put a portable tank in the boot and go for a drive down to single digits DTE before putting in some gas and comparing to mfg. spec.

I've read hundreds and hundreds of posts of bmw owners with siphon related symptoms and with mine having a leak at a factory seam that has no seal, i'm sensing 'design defect'; people end up replacing a $100 part which is perfectly functional other than there is no 50¢ o-ring.

It appears the seal is supposed to be a "flare" like used in natural gas connections however it's made from plastic and no way to tighten.

It was tragically difficult to get o-rings into that seal, if i ever have to do again, i will use a piece of rubber tube around the OUTSIDE of the seal and a hose-clamp.

I have extreme confidence that people are replacing the whole sender unit or jet pump assembly when they probably just need a seal.

Some possible failure points if your jet pumps aren't working:

clogged venturi valve; some people have used fuel system cleaner to get them cleaned out, some people have used 'a pipe cleaner'; if one is working and one isn't you could make some determinations by driving to a 'nose up' or 'nose down' attitude and see what happens with fuel test 6.

disconnected line to one of the jet pumps.

pressure relief valve (this is on the right side of tank)

weak main pump

pressure regulator (which is in the fuel filter)

A couple pretty easy checks you can 'poor man mechanic' try (no special tools needed).

Start with about 1/4 tank of gas then:

pull the right side pump out an inch or so, use mirror if needed and of course a flashlight and observe the jet pump outlets and the pressure relief valve.

gas should be pumping like crazy out of the two outlet hoses and NOT a drop from the pressure relief valve.

pull the left side sender out an inch or so and observe the seals and connection at the interface from the hoses to the sender unit (that's where my failures were)

put a 't' connector in and get some pressure readings. 1 to 1.3bar on the return line (l'll leave it to you to do the math if your gauge is psi).

I've put this other places but deserves mention logically here as well.

There are some myths about gas and running low on the gauge, they are all false, but the big ones are here:
Don't run below a quarter tank, the pump is cooled by being submerged and won't be cooled properly.

absolutely false; on the bmw x5, since the pump is in the surge chamber (aka reserve tank), it will be submerged until the car gets to about 2 or 3L of gas, in addition, any time you get below about a half a tank, the car is always using 'the last 5L of gas' it literally means once you get below half a tank, the car is operating at 1/12 of a tank always (until the low fuel light comes on). (At which point it will happily operate down to less than 1/30 of a tank)
Don't run below a quarter tank; it will increase the relative amount of sediment that also can cause problems for the fuel system.
absolutely false. When i opened up the tank of my wife's car with 131313 miles (should I be surprised it had bad luck)? There was more dirt in the tank from me opening the tank than the 400 fill-ups that preceded my work. (quite literally; i knocked a crumb of dirt in there and it was the only thing i saw in the crystal clear gas).

On the left side of the tank there is a 'dent' to align the sender unit and because gas stays there permanently there was a little dirt in there; maybe about 0.2g worth, the rest of the tank stays perfectly clean because it's constantly swirled to shake up any dirt that could settle, the jet pumps move the fuel to the surge tank and unless the dirt is too big to fit through the pre-screen filter at the foot of the pump that dirt will end up in the fuel filter; which is ginormous; literally 50-100x the size of the 'old school' inline fuel filters of yore.
Don't use less than 1/4 tank when it's cold; the water in the gas will find a low spot and freeze.
You would have to have 'powerball' level of bad luck to get crappy enough gas for this to happen. I run my car down to single digit DTE about 3-4 times per year and it does not matter if the temp outside is below zero, the gas delivery is flawless; I live in the midwest so have to use 'crappy gas' with ethanol which dissolves any water that could be in the tank and burns it up.

I really hope that many people can learn what they need to actually solve this problem without the 20-30 hours of research and 10 or so hours in the garage, armed with the knowledge here that is literally a work week worth of research condensed into half an hour, you should be able to diagnose the problem accurately and more than likely fix your problem without even having to replace parts.

Learn how to use the hidden test menu, it's the only way to diagnose fuel supply system problems, but know what 'working' looks like; get a control reading when your x5 is operating properly.

Be aware that it's likely each x5 may read slightly differently but that your car should be basically the same always.

Once the tank is below about half, at this point, all the fuel being consumed is coming from the 8L reserve tank, it's absolutely vital for the siphon jet pumps to be operating or you will run out of gas with 70 miles on the distant to empty.

please report back if this thread helped you solve your 'sucking problem'.

-awr
Dear andrewwynn!

Very useful writeup!!
Based on your description, i found the fault in 10 minutes.

Many thanks!!
Attached Images
 
Reply With Quote
  #173  
Old 09-10-2021, 06:14 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
It's a design flaw. Every one will eventually do that. So glad it helped
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #174  
Old 09-14-2021, 09:44 AM
Member
 
Join Date: Mar 2016
Location: Washington State
Posts: 19
lovbyts is on a distinguished road
I just have one questions (yeah probably not true) why does BMW have to make everything so damn complicated? Well a few things are simple enough like the radiator hoses but most everything else is a PITA.

Yeah Ive already had the fuel pump failure.
__________________
2001 3.0 BMW X5
Reply With Quote
  #175  
Old 09-14-2021, 11:48 AM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
Solving one problem after another over time leads to complexity. It's impractical to ground up design every time and that method leads to an entirely different type of failure mode.

Considering the permanent fix for the o-ring design flaw is a single zip tie BMW could have sent out a TSB vs. replace the whole left sender unit with the same design flaw as the original.
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #176  
Old 09-14-2021, 11:54 PM
Member
 
Join Date: Mar 2016
Location: Washington State
Posts: 19
lovbyts is on a distinguished road
Quote:
Originally Posted by andrewwynn View Post
Solving one problem after another over time leads to complexity. It's impractical to ground up design every time and that method leads to an entirely different type of failure mode.

Considering the permanent fix for the o-ring design flaw is a single zip tie BMW could have sent out a TSB vs. replace the whole left sender unit with the same design flaw as the original.

They really need to add a like button to the post so we can simply hit like and not have to waste post section. Thanks for all the great information even though Ive gotten information overload from it again.
__________________
2001 3.0 BMW X5
Reply With Quote
  #177  
Old 09-17-2021, 12:10 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
AWR-fix: e53 Fuel pump / siphon pump details

Quote:
Originally Posted by lovbyts View Post

They really need to add a like button to the post so we can simply hit like and not have to waste post section. Thanks for all the great information even though Ive gotten information overload from it again.

Sometimes I get a like button in tap a talk but usually no so maybe it's based on which forum I don't really pay attention to which forum I'm in I just reply to subscribed threads.


Confirmed. Bimmerfest has like option
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)

Last edited by andrewwynn; 09-17-2021 at 12:18 PM.
Reply With Quote
  #178  
Old 09-17-2021, 12:32 PM
bcredliner's Avatar
Premier Member
 
Join Date: Jun 2008
Location: Little Elm,Texas. (40 minutes North of Dallas)
Posts: 8,105
bcredliner is on a distinguished road
I would rather not have a like button as it is becomes too easy just to punch it rather than state the reason for ones opinion or provide input which is one of the primary purposes of a forum.

In addition, if there were a like button then there should also be a I don't like button and, and, and and.
__________________
X5 4.6 2002 Black Sap, Black interior. 2013 X5M Melbourne Red, Bamboo interior
Dallas
Reply With Quote
  #179  
Old 09-17-2021, 12:52 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
"like".

Well said. I have often posted simply +1 when in agreement with a post it means the same as "like"

So: "+1".
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #180  
Old 03-10-2023, 11:10 AM
Member
 
Join Date: Nov 2010
Location: USA
Posts: 109
zonefive is on a distinguished road
My gauge does not go to full after I fill the tank. On the menu it usually initially says the right side of the tank is zero, and will sometimes flicker between 27 and zero as I am driving around, and will display Phase2.

After a period of time, the gauge will go to full and the menu will show both sides of the tank as full, but will still show Phase2.

After more time, usually after about 50 miles/a few days, the indicator will switch to Phase1 and the gauge will be completely normal.

I'm suspecting the fuel level sensor on the right is the culprit. I'm on my third fuel pump. The mechanic says it is the cluster. I don't have time to fix the car myself, and it is really hard to find a good mechanic. Is it the pump/sensor on the right side?? Or the cluster?

The photo shows the menu with a full tank (it is in phase2) but the needle doesn't go to the top until later. Video shows the right tank flipping back and forth between zero and full. Any advice is appreciated.

Video: https://youtu.be/GV8Ywc4fOm8
Attached Images
 
__________________
Mark
2001 3.0 Original Owner, still going
2012 E70 xDrive 35i Pre-Owned -- sold because no one could figure out the transmission problem

Last edited by zonefive; 03-10-2023 at 11:31 AM.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 05:05 PM.
vBulletin, Copyright 2024, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.