|
Xoutpost server transfer and maintenance is occurring.... |
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
|
LinkBack | Thread Tools | Display Modes |
#51
|
|||
|
|||
Quote:
Similarly, a reamer is typically used to take off a few thousandths (or less) (of an inch) to make a hole's dimensions to a very tight spec. They're not typically intended for hogging out clearance holes. So I have my doubts on the reamers too. But this "super drill" - WOW. A little googling led me to: PracTool | Super Drill and the full size youtube video: https://www.youtube.com/watch?v=a-jQXtJMv6Q It's like an inverted lathe. I used to do some machining back in the day, both for machining research and for building the machine prototypes to do the research, and this super drill is a much more professional way to do it. The only challenge I can see that this superdrill would have would be the relative hardness of the CV joint tool you're trying to cut vs. the cutting tip on this tool (should be carbide, but I did not see that mentioned). That is really an awesome invention. Thanks for posting that. Learning stuff like that is the main reason I read these forums.
__________________
2001 X5 3.0i, 203k miles, AT, owned since 2014 |
Sponsored Links | |
|
#52
|
|||
|
|||
Yes, I was pretty sure the step drill wasn't going to work either. The super drill has a fairly high grade carbide insert and the tool doesn't seam that hard, easily filed. I bought the super drill many years ago at a farm show because I was really impressed with the idea. I haven't used it that often but it sure comes to the rescue when I do!
__________________
1988 325is (purchased new) sold 2004 X5 3.0 2005 X3 2.5 2008 X5 3.0 (new to me) |
#53
|
|||
|
|||
Quote:
|
#54
|
||||
|
||||
I want to replace a boot soon. I'm planning to make some type of fork to pull it off.
I'm actually thinking of taking a piece of 1/2" plate, drilling a 27mm hole in the center and a couple 3/4" holes a couple inches offset from center each way. Fabricate another piece from similar stock but with a hole the diameter of the driveshaft. Cut that piece in half at an angle so I can use some 3/8 bolts to re-attach around the shaft and grab it tight. Then a pair of 3/4 threaded rods some washers and 4 nuts to spread the plates apart. The same tool could be used to compress it back together..
__________________
2011 E70 • N55 (me) 2012 E70 • N63 (wife) |
#55
|
|||
|
|||
I was just planning on using my 1/2" 18v Makita on lowest gear. My small drill press is too fast. How did you make out with the die grinder?
__________________
1988 325is (purchased new) sold 2004 X5 3.0 2005 X3 2.5 2008 X5 3.0 (new to me) |
#56
|
|||
|
|||
My new bits haven't arrived yet. I'll be on it as soon as they do.
|
#57
|
||||
|
||||
DIY: CV Joint Removal Tool anyone?
I talked to my brother today he's going to build the x5 specific CV pull apart tool for doing boot replacement.
His shop has EDM so can cut 90° corners in steel so we will have the center hole for the shaft split where a couple 3/8 bolts can clamp it together tightly. A pair of threaded rods will provide push and pull capacity to pull apart and press together. I'll post the design for others to copy. The most difficult part will be drilling 1 1/16" hole for the hub side. It would be a reasonably small kit to mail so pass around very possible. I was thinking of making the design with just one rod from one side but as the simplicity of the design started to come to fruition I decided better to keep the forces balanced. I haven't measured anything yet to figure out what sizes are needed. I'm going to try to use locally available threaded rod so it's easy to reproduce. it probably can work with 1/2" rod for sure 5/8. Not sure if can get 3/4 locally. I revised the design to the bottom style it will be a little easier to handle though thinking it though might not be as strong so the original middle design.
__________________
2011 E70 • N55 (me) 2012 E70 • N63 (wife) Last edited by andrewwynn; 12-27-2018 at 02:27 PM. |
#58
|
|||
|
|||
If you just want to replace the boot (vs. removing the complete outer joint), I don't know why you would need any sort of tool like this.
I changed the boots on my right front axle without even touching the axle nut or brakes, etc. The outer part of the outer CV joint stayed exactly where it was the whole time. When I did that job, I already had this special tool in hand, ready to use, and was not even able to see if it would fit - never had a need for it. Specifically, I had a failed outer boot. I kind of followed the famous "30 minute CV boot" thread on this forum (link below). By far, the most difficult part of the whole job was trying to understand what the thread was trying to say - until wpoll and cn90 came to the rescue. So I separated at the inner joint / tripod. Then when trying to get the tripod off the axle (outer end still fully attached), expecting the outer joint to not let loose so easily, I gently used a slide hammer rather than a puller to pull it off. Well, the outer joint easily separated, so I continued the work with the axle fully removed from the car. But the outer joint very easily separated - it is held only by a c-ring in a square channel that pops out relatively easily. What happened in my case is described below. https://xoutpost.com/bmw-sav-forums/...ml#post1135021 I thought all the discussion here about this tool was if you wanted to carefully separate the outer joint, after you've removed it from the hub/spindle/carrier.
__________________
2001 X5 3.0i, 203k miles, AT, owned since 2014 |
#59
|
|||
|
|||
Got my bit set yesterday. Got on my CV removal tool today. Took about one hour to ream it out with my die grinder. Took it from 29.5mm (the true dimension, not 30mm) to approx. 34.5 mm. That should be wide enough to clear the splined part of the half shaft. We'll see tomorrow.
|
#60
|
||||
|
||||
Quote:
https://xoutpost.com/1108115-post18.html Next time I'll use my 10# slide hammer instead.
__________________
2006 Infiniti G35 2001 BMW 3.0I E53 X5 Build date 08/2000 SOLD Lotus Europa 1970 Destroyed by fire Lotus Europa 1970 S2 Renault Powered Lotus Type 52 1970 Twincam Webers Powered PORSCHE 911 Targa 1982 The Garage Queen Audi Avant donated to Kars for Kids BMW 525IT Sold Audi 4000CS Quattro Sold Jensen Healey Lotus Powered Sold Opel 1900 Sold Triumph Spitfire 1971 Sold Triumph Spitfire 1968 Sold Plymouth "Cuda" 340 Six pack SOLD |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|
|