Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > X5 (E53) Forum
Arnott
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 07-17-2021, 03:04 PM
Member
 
Join Date: Nov 2014
Location: SF Bay Area
Posts: 1,423
oldskewel is on a distinguished road
Subframe bushing replacement instructions?

I have the bushings (Lemfoerder) and the eBay tool kit to replace the 4x bushings on the rear subframe of my 2001 3.0i E53.

I have searched high and low for instructions on how to do the job. The following video is the closest I can find to something useful (plenty of bad videos, too):
https://www.youtube.com/watch?v=kD8winbz8kE

But I was hoping to get a set of instructions saying how to do it, lubricant for removal and assembly, alignment of bushings if that matters, etc. Found nothing at all anywhere, even from the kit, as if it is so easy and obvious that no instructions are needed. I can make that work, but still was hoping to find something written. Any ideas?
__________________
2001 X5 3.0i, 203k miles, AT, owned since 2014
Reply With Quote

Sponsored Links

  #2  
Old 07-17-2021, 03:34 PM
Member
 
Join Date: Mar 2016
Location: Saskatchewan Canada
Posts: 2,053
80stech is on a distinguished road
It's pretty straight forward. Muffler hangers can be bent out of the way. Torch(even just propane) heat helps with removal. Maybe clean the hole with a flap wheel. I just used some anti-sieze for assembly. Watch the alignment.
__________________
1988 325is (purchased new) sold
2004 X5 3.0 2005 X3 2.5
2008 X5 3.0 (new to me)
Reply With Quote
  #3  
Old 07-17-2021, 10:45 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
I think my Repair manual has the steps. I'm about to do the procedure myself. If it's in there I'll make a PDF for you.
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #4  
Old 07-18-2021, 12:16 AM
Member
 
Join Date: Nov 2014
Location: SF Bay Area
Posts: 1,423
oldskewel is on a distinguished road
Funny, I had not thought the Bentley would have useful info on this, due to using the special tool. But I looked it up, scanned and attached here.

In there it does have some good, solid info, such as bushing alignment (arrows fore-aft within 7*) and lubricant (Circolight - googled on that for a while, and will probably use dish soap as a substitute). Also pre-heating prior to removal, with a heat gun with < 600*C for < 2 minutes.

Also solid, but wrong is the spec on torquing those M14 bolts. The Bentley says "163 Nm (94 ft-lb)", but those values are not the same. I'll probably go with the 94 ft-lb if they're class 8.8, or 163 Nm if they're class 10.9.

I'll guess how to make the eBay tool work should be self explanatory, or will rely on that youtube linked above. I know none of this is difficult.

But if I were to follow the Bentley literally, I would first drop the subframe 2", which includes a bunch of other things like disconnecting the differential and removing the exhaust. I know those are not strictly required, so I will have to guess what is actually required. I'll probably just try to do none of the extra stuff until I'm forced to.

I've seen many reports of people bending the exhaust hanger to get the required clearance, vs. the Bentley says to remove the exhaust (so you don't need to bend anything). I know my exhaust comes off pretty easily, so that's one I won't mind doing.

Name:  subframe bushings bentley_Page_1.jpg
Views: 1179
Size:  74.2 KB

Name:  subframe bushings bentley_Page_2.jpg
Views: 1171
Size:  69.0 KB

Name:  subframe bushings bentley_Page_3.jpg
Views: 1242
Size:  84.2 KB
__________________
2001 X5 3.0i, 203k miles, AT, owned since 2014
Reply With Quote
  #5  
Old 07-18-2021, 01:22 AM
Member
 
Join Date: Mar 2016
Location: Saskatchewan Canada
Posts: 2,053
80stech is on a distinguished road
As far as I remember you don't have to remove anything. Do one side at a time and you might have to pry down a bit for clearance depending how bad the bushings are. It's a bit of a work-out though so I would schedule in a beer break
__________________
1988 325is (purchased new) sold
2004 X5 3.0 2005 X3 2.5
2008 X5 3.0 (new to me)
Reply With Quote
  #6  
Old 07-18-2021, 02:59 AM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
"break". Real men use "beer" as a unit of time. Eg "that will take about three beers to change that out"

Bwahhaahhaa
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #7  
Old 07-18-2021, 12:55 PM
Member
 
Join Date: Jun 2020
Location: NC
Posts: 32
lichtman is on a distinguished road
I did mine with the subframe completely off of the vehicle a couple months back. you can totally do it with the subframe still attached to the car (one side at a time). I had my subframe off for other reasons. As I recall the Bently manual suggested heating the bushing area of the subframe with a hot air gun for a bit to aid removal. As for installation I got some of this:

https://www.amazon.com/IPC-Emulsion-...ct_top?ie=UTF8

It's made for rubber parts, and made pressing the new ones in a breeze.

Good Luck!
Reply With Quote
  #8  
Old 07-18-2021, 03:56 PM
Henn28's Avatar
Member
 
Join Date: May 2021
Location: Louisiana
Posts: 714
Henn28 is on a distinguished road
Quote:
Originally Posted by 80stech View Post
As far as I remember you don't have to remove anything. Do one side at a time and you might have to pry down a bit for clearance depending how bad the bushings are. It's a bit of a work-out though so I would schedule in a beer break
Agreed, mine were a workout for sure. First one came right out, but subframe alignment and creating space for the tool on top of the bushing became increasingly difficult for the remaining 3. I was able to use a pry bar for the second one but then had to loosen the bolts on the other side and start to let the subframe down on all four corners and pry liberally.
Reply With Quote
  #9  
Old 07-18-2021, 08:00 PM
Member
 
Join Date: Jan 2013
Location: Finland
Posts: 1,376
Clavurion is on a distinguished road
Put new bushes in the freezer prior to installing them so they shrink a bit and warm the subframe again after removing the old bushes. If you use any lubricant be sure it's water soluble. The connection between bushing and subframe is supposed to be solid soon after installation so any permanent petroleum based lubricant is out of the question.
__________________
E39 530dA -02 M-Sport Messing metallic
E53 X5 3.0dA -06 Sport Stratus grey
Reply With Quote
  #10  
Old 07-18-2021, 08:05 PM
Member
 
Join Date: Jan 2013
Location: Finland
Posts: 1,376
Clavurion is on a distinguished road
Quote:
Originally Posted by 80stech View Post
As far as I remember you don't have to remove anything.
Depends on the type of exhaust. At least on V8 models the hanger for rear silencers is directly on the way while doing the rear subframe bushes so either remove the exhaust or warm up and bend the hanger out of the way.
__________________
E39 530dA -02 M-Sport Messing metallic
E53 X5 3.0dA -06 Sport Stratus grey
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 12:25 PM.
vBulletin, Copyright 2024, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.