Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > X5 (E53) Forum
Arnott
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 04-17-2022, 06:17 PM
workingonit's Avatar
Member
 
Join Date: May 2021
Location: DFW Texas
Posts: 730
workingonit is on a distinguished road
reset fuel trims; lasted about 60 miles or about an hour

I accidently reset my fuel trims, by unplugging the MAF sensor repeatedly several times while it was running. The very high long term fuel trims went to zero, and the short terms stayed low while idling. Well, I finally found out how I accidently reset my fuel trims...it was by repeatedly unplugging and re-plugging the MAF sensor
https://www.e46fanatics.com/threads/.../post-14695303
Quote:
Originally Posted by wamcdonald
With car running disconnect the MAF sensor wait a few seconds and reconnect it, that's it. The car may stall but just re-start and you may through a MAF code but this gets the values back to zero.
I hate mysteries, so that's reassuring that it's been done before, with the same results.

That was over a week ago, and today I took the X5 on a >100 mile trip, just to see how long/how many miles the "reset" fuel trims were good for; I refer to this previous post, where I pondered this question: https://xoutpost.com/1219167-post35.html.

Now I know...if I haven't solved the SES light problem, as triggered by P0171, P0174, and P0313 codes (where the fuel trims are very high) before inspection time in October, I might have as long as 60 miles and/or about an hour of drive time before the fuel trims go sky-high again, and set off the SES light (I saw and marked the time and mileage as the SES came on).

andrewwynn
had suggested the reset adaptations may be able to gain a week's grace period, as a grace period at inspection time;
Quote:
Originally Posted by andrewwynn
reset adaptations may get you a week or more no error code to get an inspection pass while working out the problem
what adaptations he meant, I don't know, but while I'm trying just about anything to resolve the problem (visual inspections, smoke test(s), carb cleaner spray test, MAF cleaned and tested, O2 sensor functions tested OK, etc.), with no problem source found, I'm willing to cheat a bit to pass the test.

My X5 is just under 21 years old, runs perfectly fine, no hint of a smelly or rich exhaust (to my senses), and though the scan tool says that there is an infrequent lean misfire, my "seat of the pants feel for the car I'm in" tells me no such thing. It runs smooth as silk at any speed, from a 700 rpm idle to 80 mph.

Anyone care to venture a new approach? or will I end up praying to get a one hour or 60 mile window of opportunity, where my X5 can pass inspection? If it was just 4 years older....
__________________
01 BMW X5 E53,3.0i-5L40E, 7/13/01
topas-blau,Leder-grau,"resto-project car"

Here:
14 Lexus ES350,3.5L-U660E
09 HHR Panel,2.2L-4T45E
04 Chevy 2500HD,6.0L-4L80E
98 GMC Sierra 1500,5.7L-4L60E

Gone:
66 Chevelle Malibu 2dr ht.,327>441c.i.-TH350>PGlide/transbrake
08 Cobalt Coupe,2.2L-4T45E
69 & 75 C10s,350c.i.-TH350
86 S10,2.8L-700R4
73 Volvo 142,2.0L-MT4
72 & 73 VW SuperBeetles,1.6l-MT4
64 VW,1.2l-MT4
67 Dodge Monaco 500 2dr ht.,383c.i.-A727
56 Chevy 210 4dr,265c.i.-PGlide
Reply With Quote

Sponsored Links

  #2  
Old 04-17-2022, 06:20 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
reset fuel trims; lasted about 60 miles or about an hour

With my foxwell scanner I can reset adaptations in the service main menu I think. (I never remember the exact places). I am sure the think diag will also but I'm likely to let the subscription expire on that. The foxwell is more reliable even though I do like the iPhone interface.

Have you checked your fuel pressure under load? Pumps at end of life just get weak. The FPR hides their failure for an extended time, often after more than a year you just start getting lean codes that aren't MAF or vacuum leaks.

The car measures how much fuel by assuming 50.00 psi.

If its less, even if just under high throttle you'll get lean condition. Watch a graph of your O₂ precat and see if they go lean under heavy throttle that's a big clue.
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #3  
Old 04-17-2022, 07:50 PM
workingonit's Avatar
Member
 
Join Date: May 2021
Location: DFW Texas
Posts: 730
workingonit is on a distinguished road
perhaps a clue that I can follow?

Quote:
Originally Posted by andrewwynn View Post
With my foxwell scanner I can reset adaptations in the service main menu I think...Have you checked your fuel pressure under load? Pumps at end of life just get weak. The FPR hides their failure for an extended time, often after more than a year you just start getting lean codes that aren't MAF or vacuum leaks.

The car measures how much fuel by assuming 50.00 psi.

If its less, even if just under high throttle you'll get lean condition. Watch a graph of your O₂ precat and see if they go lean under heavy throttle that's a big clue.
In one of my posts I said I saw a "reset adaptations" somewhere in the service section, on my Foxwell 510, but was afraid to do it (it said reset ALL adaptations). Not knowing the full scope of adaptations involved, I didn't want to screw-up some other adaptation that was beneficial to the operation of the X5. I'll have to revisit the service section next week, after I return from my trip.

Once, I had trouble with my '04 2500 HD re-learning, after just fixing something or other (15 years ago, I can't remember what it was, but that it made the 120 mile round-trip commute very interesting the next morning/afternoon....)

Concerning fuel pressure, that could be why the P0313 code sometimes appears, along with P0171 & P0174. P0313 is when the PCM has detected a misfire in one or more of the engine's cylinders along with a low fuel reading in the fuel tank. I've been meaning to get this one, which I believe has been recommended on this forum
Name:  OTC fuel pressure tester.jpg
Views: 1144
Size:  45.3 KB

As I stated above, I've been getting "lean codes that aren't MAF or vacuum leaks". Here's an O2 graph I made earlier;
Name:  O2 graph1.jpg
Views: 1098
Size:  275.0 KB

does it show what you're talking about here?
Quote:
Originally Posted by andrewwynn
Watch a graph of your O₂ precat and see if they go lean under heavy throttle that's a big clue.
I have no maintenance records for this X5, and the guy I got it from didn't touch the fuel system at all, focusing on (in order) cooling system, suspension, axles, exhaust, "cracked" windshield, & timing chain/guides (plus other stuff). He didn't know what the previous owner had done, except for screwing up the radio (though he had kept the high-mileage truck moderately well serviced, with 4 of 6 door locks OK, all windows & lights working, A/C perfect condition, etc.).

This nagging problem is something that appeared 5 months into my ownership, but not prior. It may just be as you say, time for the FPR to get weak.
__________________
01 BMW X5 E53,3.0i-5L40E, 7/13/01
topas-blau,Leder-grau,"resto-project car"

Here:
14 Lexus ES350,3.5L-U660E
09 HHR Panel,2.2L-4T45E
04 Chevy 2500HD,6.0L-4L80E
98 GMC Sierra 1500,5.7L-4L60E

Gone:
66 Chevelle Malibu 2dr ht.,327>441c.i.-TH350>PGlide/transbrake
08 Cobalt Coupe,2.2L-4T45E
69 & 75 C10s,350c.i.-TH350
86 S10,2.8L-700R4
73 Volvo 142,2.0L-MT4
72 & 73 VW SuperBeetles,1.6l-MT4
64 VW,1.2l-MT4
67 Dodge Monaco 500 2dr ht.,383c.i.-A727
56 Chevy 210 4dr,265c.i.-PGlide
Reply With Quote
  #4  
Old 04-17-2022, 07:51 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
reset fuel trims; lasted about 60 miles or about an hour

The reset all is the one. Some scanners will have fuel adaptation foxwell doesn't.

Tye O₂ trace shows what I described. I haven't done a trace in a while. Usually you'll get a trace peg high or low when you get off throttle and coast or wot but uner load say going up a long hill the pre cat should bounce up and down a few times a second spending about the same time up as down.

Definitely get a fuel pressure gauge. On e53 petrol model the pressure should be dead flat 50.0 ± 1psi (but stay steady e.g. 49.5 ± 0.05). Usually it's the FPR which has an internal o-ring that fails but second most likely is fuel pump wearing out.

Divide your total miles by your long term average speed. Eg 150000/28.5=5263.158.

Pump should last 5000-5500 hours. 6000 if lucky.

(Reminding myself my new to me e70 is about 148000/5500=26.909 so I'm probably due for a fuel pump soon. I'll maybe order to have one on hand when it fails. )
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)

Last edited by andrewwynn; 04-17-2022 at 08:00 PM.
Reply With Quote
  #5  
Old 04-17-2022, 08:30 PM
workingonit's Avatar
Member
 
Join Date: May 2021
Location: DFW Texas
Posts: 730
workingonit is on a distinguished road
210620 divided by 28.6 equals tired FPR

210620/28.6 (these numbers are from memory, but very close to actual)=7364.33 hours, if original. It probably isn't though; surely the original owner replaced it in the past. However, the problem started surfacing on hard(er) braking on a turn, followed by acceleration, or on a sudden evasive manuever, followed by hard acceleration.

Today's SES trigger occurred when hard braking at the merging of lanes of traffic near a wreck scene, though I had been expecting the SES to appear at any time, as I watched the fuel trims grow steadily higher, with long-terms already at 11.72% each, and the short-terms fluctuating between -2.36 % and 10.17% (as observed).

I'll have to put aside some of my spending money from my upcoming camping trip, and buy the fuel pressure test kit, secretly. My wife says I buy too many things for an old retired guy (money that she wants to spend!).
__________________
01 BMW X5 E53,3.0i-5L40E, 7/13/01
topas-blau,Leder-grau,"resto-project car"

Here:
14 Lexus ES350,3.5L-U660E
09 HHR Panel,2.2L-4T45E
04 Chevy 2500HD,6.0L-4L80E
98 GMC Sierra 1500,5.7L-4L60E

Gone:
66 Chevelle Malibu 2dr ht.,327>441c.i.-TH350>PGlide/transbrake
08 Cobalt Coupe,2.2L-4T45E
69 & 75 C10s,350c.i.-TH350
86 S10,2.8L-700R4
73 Volvo 142,2.0L-MT4
72 & 73 VW SuperBeetles,1.6l-MT4
64 VW,1.2l-MT4
67 Dodge Monaco 500 2dr ht.,383c.i.-A727
56 Chevy 210 4dr,265c.i.-PGlide
Reply With Quote
  #6  
Old 04-17-2022, 08:44 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 10,817
andrewwynn will become famous soon enough
You can likely borrow the tester from auto parts store
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #7  
Old 04-18-2022, 12:38 AM
RocketyMan's Avatar
Member
 
Join Date: Jan 2020
Location: PNW
Posts: 553
RocketyMan is on a distinguished road
On your MAF and in neutral with literally no engine load, what is your g/s on your MAF holding the engine RPM at exactly 1000 rpms? What about at 1500 rpms. Then what about at 2000 rpms.
__________________
2003 BMW X5 3.0i -- MT5, 3.64s final gears, H&R lowering springs, K-Mac bushing kit
2007 BMW X3 3.0Si -- MT6
Reply With Quote
  #8  
Old 04-18-2022, 02:09 PM
workingonit's Avatar
Member
 
Join Date: May 2021
Location: DFW Texas
Posts: 730
workingonit is on a distinguished road
almost steady, +/-

Quote:
Originally Posted by RocketyMan View Post
On your MAF and in neutral with literally no engine load, what is your g/s on your MAF holding the engine RPM at exactly 1000 rpms? What about at 1500 rpms. Then what about at 2000 rpms.
I went outside to prepare my camper for my trip, and since I had to move the X5 aside to pull the trailer out of the garage, I grabbed these photos of my Torque Pro-dedicated phone in the X5.
Name:  the usual suspects.jpg
Views: 1075
Size:  127.1 KB the usual suspects

Name:  MAF graph at 1k, 1.5k, 2k rpms.jpg
Views: 1095
Size:  91.7 KB MAF graph at 1k, 1.5k, 2k rpms

I had trouble keeping the speed exactly on the marks of 1k, 1.5k, and 2k rpms, but it is close enough. 1k yields roughly 6 g/s, 1.5k yields about 8 g/s, and 2k rpm yields slightly over 10 grams per second.

Since a rule of thumb on a MAF's air flow rate at 500 rpm is 1 gram per second per liter of engine displacement (or 3g/s for my 3.0l), my graph is just about right at 6g/s at 1k rpms, a bit low at 1.5k rpms, and really low at 2k rpms (it should be 3x4=12 g/s). Am I reading this correctly? I did read the MAF momentarily, while driving at 70mph yesterday, it read 20+ g/s. I forgot the rpm, though.
__________________
01 BMW X5 E53,3.0i-5L40E, 7/13/01
topas-blau,Leder-grau,"resto-project car"

Here:
14 Lexus ES350,3.5L-U660E
09 HHR Panel,2.2L-4T45E
04 Chevy 2500HD,6.0L-4L80E
98 GMC Sierra 1500,5.7L-4L60E

Gone:
66 Chevelle Malibu 2dr ht.,327>441c.i.-TH350>PGlide/transbrake
08 Cobalt Coupe,2.2L-4T45E
69 & 75 C10s,350c.i.-TH350
86 S10,2.8L-700R4
73 Volvo 142,2.0L-MT4
72 & 73 VW SuperBeetles,1.6l-MT4
64 VW,1.2l-MT4
67 Dodge Monaco 500 2dr ht.,383c.i.-A727
56 Chevy 210 4dr,265c.i.-PGlide
Reply With Quote
  #9  
Old 04-18-2022, 03:48 PM
Premier Member
 
Join Date: Jan 2016
Location: Michigan
Posts: 397
ahlem is on a distinguished road
What’s the history on your fuel injectors and injector o rings?
__________________
2001 x5 3.0 (sold with broken motor), 1990 e30 M3, 1991 318is, 2002 325i, 2008 335i Dinan stage 3 6 speed,
Reply With Quote
  #10  
Old 04-18-2022, 05:11 PM
workingonit's Avatar
Member
 
Join Date: May 2021
Location: DFW Texas
Posts: 730
workingonit is on a distinguished road
????

Quote:
Originally Posted by ahlem View Post
What’s the history on your fuel injectors and injector o rings?
I've no history at all, except what I saw being done by my neighbor over 3.5 years, or what he told me about, after he moved away, prior to the swap. I don't recall him talking about the injectors or ignition, just the cooling system re-do, and the timing chain/guides renew, concerning the engine. It runs so smooth, I don't believe he didn't upgrade something in there, before he handed it off to me.

I've had no contact with him in several months now, so it might be time to try and contact him again, just for more history on the X5.
__________________
01 BMW X5 E53,3.0i-5L40E, 7/13/01
topas-blau,Leder-grau,"resto-project car"

Here:
14 Lexus ES350,3.5L-U660E
09 HHR Panel,2.2L-4T45E
04 Chevy 2500HD,6.0L-4L80E
98 GMC Sierra 1500,5.7L-4L60E

Gone:
66 Chevelle Malibu 2dr ht.,327>441c.i.-TH350>PGlide/transbrake
08 Cobalt Coupe,2.2L-4T45E
69 & 75 C10s,350c.i.-TH350
86 S10,2.8L-700R4
73 Volvo 142,2.0L-MT4
72 & 73 VW SuperBeetles,1.6l-MT4
64 VW,1.2l-MT4
67 Dodge Monaco 500 2dr ht.,383c.i.-A727
56 Chevy 210 4dr,265c.i.-PGlide
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 08:08 PM.
vBulletin, Copyright 2024, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.