N62 Valve Stems Seals - What was your cost

[A B Able Truck]

Originally Posted by admranger

I saw his video (in amazing low-def 240p!) online. I had heard of using a leak down tester to hold the valves in place while you remove the valve springs, etc. as a quick way to change out valve springs from some racers. Never thought of it for this application but it makes sense. Very clever.
Still a whole lotta parts gotta come out to get access to the valves! For me, I'm likely to just drive down to Escondido, drop the X5 off and spend the day with friends! Better way to spend the day for me!

You may have watched a video from another shop here in town. I don't think AGA (All German Auto) has released their video yet. The other shop with the "amazing low-def 240p" is probably Escondido German Auto (E.G.A).

[admranger]

Originally Posted by A B Able Truck

You may have watched a video from another shop here in town. I don't think AGA (All German Auto) has released their video yet. The other shop with the "amazing low-def 240p" is probably Escondido German Auto (E.G.A).

I think you are correct. My error.

Regardless, creative solutions to otherwise debilitatingly expensive issues are nice to see!

[SlickGT1]

Originally Posted by admranger

I saw his video (in amazing low-def 240p!) online. I had heard of using a leak down tester to hold the valves in place while you remove the valve springs, etc. as a quick way to change out valve springs from some racers. Never thought of it for this application but it makes sense. Very clever.

Still a whole lotta parts gotta come out to get access to the valves! For me, I'm likely to just drive down to Escondido, drop the X5 off and spend the day with friends! Better way to spend the day for me!

I hope it is more than just that. I have seen this method performed many times. You need to make sure you get your valves to the closed position. Then there is a tool specifically made to remove and install the valve stem locks.

While the air is being pumped into the cylinder, you whack the locks with said tool, and you got the locks off. Remove, replace seals and move on.

This.
Motion Pro Valve Core Remover - Dirt Bike Motocross - Motorcycle Superstore

And Leak down tester used to pump air in.

I hope A B has a cooler way to do this.

[KyleNatolix5]

Dealership told me it's an 8K job as well. I contacted the master tech who does the job, he definitely knows his stuff. For 8k you might as well get a different engine installed. As of now I'm going through a an oil change jug a month until I get it done. I'll be replacing the cats after the job when the time comes around with some aftermarket "high flow" units. My X is running full steam ahead as of now, but I'm sure it can't be to healthy for it to be blowing that much oil out the exhaust.

[A B Able Truck]

Authorized sneak peek of new N62 valve stem seal tool by All German Auto - Escondido, CA



Allows you to replace the valve stem seals on a BMW N62 without removing the cams.
The tool kit will be complete.
Valve compression rods for intake and exhaust.
Brushes to plug oil returns.
Ratcheting wrench for compression.
Control handle for compression rods.
Spark plug hole plugs with center bore for T. D.C indicator.
6.0 mm valve keeper install tool.

** Will be available in about a month **

[Doru]

Allen, will they have a detailed guide printed (or memory stick) with the tool? If not, maybe you can suggest that.

Thx!!!

[A B Able Truck]

Originally Posted by Doru

Allen, will they have a detailed guide printed (or memory stick) with the tool? If not, maybe you can suggest that.
Thx!!!

I honestly don't think I could suggest anything to Martin from AGA that he already hasn't thought of - he's a smart guy.

[A B Able Truck]

Originally Posted by A B Able Truck

I honestly don't think I could suggest anything to Martin from AGA that he already hasn't thought of - he's a smart guy.

Just to keep you interested - two more tidpits of information about the tools and process.

- A failsafe in the event you drop a keeper
- A tool that facilitates the installation of keepers in a matter of seconds

[Bulk]

Originally Posted by A B Able Truck

Just to keep you interested - two more tidpits of information about the tools and process.

- A failsafe in the event you drop a keeper
- A tool that facilitates the installation of keepers in a matter of seconds

Looking forward to it :thumb up:

The only thing that would make it better if it could be done from on the couch with a cold one...

[admranger]

Impressive!