Forum: X5 (E53) Forum
11-06-2019, 11:06 PM
|
|
Replies: 83
Views: 8,076
I think I reamed it out more than that. I'll...
I think I reamed it out more than that. I'll have to check. I had to go wider than the minimum because of the poor construction quality the ring. It was cocked, so it had to be wider for the shaft...
|
|
Forum: X5 (E53) Forum
11-06-2019, 05:23 PM
|
|
Replies: 83
Views: 8,076
You are correct, the bore as shipped is too...
You are correct, the bore as shipped is too small. I reamed mine out so the X5 splines would fit. Worked fine after doing that and grinding the top of the ring so it was perpendicular to the...
|
|
Forum: X5 (E53) Forum
11-06-2019, 03:58 AM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
11-05-2019, 10:34 PM
|
|
Replies: 83
Views: 8,076
Update:
I bought a universal tool for hub...
Update:
I bought a universal tool for hub pulling. Came with two pullers. One was mostly flat and it fit my bolt pattern. It worked quite well for pressing the axle out. It's clear it was...
|
|
Forum: X5 (E53) Forum
12-31-2018, 12:29 PM
|
|
Replies: 83
Views: 8,076
Unfortunately, I've had something come up and I...
Unfortunately, I've had something come up and I can't spend much more time on this right now. I'll try that when I have a go at it again. Right now, I have to put it back together and I'll tape the...
|
|
Forum: X5 (E53) Forum
12-31-2018, 12:34 AM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-31-2018, 12:12 AM
|
|
Replies: 83
Views: 8,076
I have hit it with PB blaster. I'm going to get...
I have hit it with PB blaster. I'm going to get after it again tomorrow. Ill rent a three jaw puller and see how it goes. This X spent 3 years in Boulder, CO so, not sure how much salt it saw, but...
|
|
Forum: X5 (E53) Forum
12-30-2018, 11:22 PM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-30-2018, 02:51 PM
|
|
Replies: 83
Views: 8,076
"I thought all the discussion here about this...
"I thought all the discussion here about this tool was if you wanted to carefully separate the outer joint, after you've removed it from the hub/spindle/carrier."
The idea is to be able to leave...
|
|
Forum: X5 (E53) Forum
12-29-2018, 11:49 PM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-27-2018, 12:48 PM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-27-2018, 01:10 AM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-25-2018, 04:41 PM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-13-2018, 11:34 PM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-13-2018, 11:37 AM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
12-12-2018, 02:11 PM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
06-20-2017, 08:51 PM
|
|
Replies: 83
Views: 8,076
|
|
Forum: X5 (E53) Forum
04-25-2017, 10:46 PM
|
|
Replies: 83
Views: 8,076
|
