We have new scans...
Since the last time I cleared this I have taken off the SES valve, cleaned it, and tested the system by hooking the valve to the pump but not the head..
The pump does infact blow through the valve, but the valve is quite hard to blow through.. I will have to scan it again and/or wait for another CEL from it to see if it is still throwing a code..
I haven't really been able to figure out how to turn on the pump and look at the MAF reading on it from INPA..
E R R O R M E M O R Y R E P O R T -------------------------------------
Date: 02/06/18 15:13:37 ECU: D_EGS JobStatus: --- - API-Job FsLesen: job status error - API-Job FsLesen: job status error
================================================== =========== Ecu : D_0056 IFH-0009: NO RESPONSE FROM CONTROLUNIT ================================================== ================================== Variant: MS430DS0 1 Error in error memory Error registration 1 : 0x005E: Error Sek. air mass meter <<<<!!! Error accurances: 2 Logistic counter : 40
Error accure 1st time at:
TCO_ST 25.96 Grad C TIA_ST -5.42 Grad C N_32 1024.00 rpm MAF 228.78 mg/stk aufgetreten vor (rel. BZ) 3.10 h
--- --- --- Error Sek. air mass meter Error to relevant Error debounce Error currently available stat. Error Error code: 5E 78 02 28 63 39 20 2A 45 B4
May have fixed this Error Sek. air mass meter but not sure yet..
================================================== ================================== Variant: LWS5_1B >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: D_00AC -1 Error in error memory ================================================== ================================== Variant: D_0070 -1 Error in error memory ================================================== ================================== Variant: LCM_IV >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: D_0066 -1 Error in error memory ================================================== ================================== Variant: D_009A -1 Error in error memory ================================================== ================================== Variant: RLS_DS2 >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: SD_DS2 >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: EWS3 >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: D_00C0 -1 Error in error memory ================================================== ================================== Variant: ZKE3_GM6 2 Error in error memory Error registration 1 : 0x00A5: mirror FT, potentiometer horizontal or cable <<<<!!! Error accurances: 1
Sporadic error
------------------------------------------------------------------------------------ Error registration 2 : 0x00AD: short circuit mirror motor BT vertical <<<<!!!
Error accurances: 1
Static error
------------------------------------------------------------------------------------================================================== ================================== Variant: D_SZM -1 Error in error memory ================================================== ================================== Variant: MRS4 >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: IKI >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: SES 1 Error in error memory Error registration 1 : 0x0091: Unknown error location <<<<!!! Error accurances: 31
Static error
Any ideas on this?
================================================== ================================== Variant: IHKA39_5 1 Error in error memory Error registration 1 : 0x001E: Auxiliary water pump <<<<!!! Error accurances: 21
Short circuit to batt+ -- -- -- Error present --Error code: 1E 41 15 85 85 00 72 01 0A 03 8F
Diagnosed this, motor is an open circuit.. Good power from wire..
================================================== ================================== Variant: D_ZUHEIZ -1 Error in error memory ================================================== ================================== Variant: RADIO >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: D_006A -1 Error in error memory ================================================== ================================== Variant: D_0048 -1 Error in error memory ================================================== ================================== Variant: D_00C8 -1 Error in error memory ================================================== ================================== Variant: BM_WIDE >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: D_00ED -1 Error in error memory ================================================== ================================== Variant: NAVMK4_2 >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: D_0048 -1 Error in error memory ================================================== ================================== Variant: NAVMK4_2 >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ================================== Variant: D_00BB -1 Error in error memory ================================================== ================================== Variant: D_SITZ_B -1 Error in error memory ================================================== ================================== Variant: D_SITZ_F -1 Error in error memory ================================================== ================================== Variant: SM53_4 >>>>>>>>>> No error found <<<<<<<<<<< ================================================== ==================================
################################################## ############## This content will stored temporary temporär in ..\inpa\sgdat\na_fs.tmp ################################################## ##############
Getting closer!! Will have her sorted soon hopefully..
Here is what I think are the "fuel trims" that I see a lot of people using to look for vacuum leaks and such..
Everything is pretty much right at zero.. That means it's good right?
I took that screenshot at idle on a fully warmed up engine..
I really don't want to pay $80 for that water pump right now and don't really want to go tearing it apart trying to fix it right now because of the water and it being super cold out situation so I'm probably not going to mess with that for a bit..
I'm getting warmed up for a catchcan and PVC conversion because this thing gets a lot lot of cold starts at 0-25 F and we do let it idle for minutes to warm up.. We leave it idle in town when we go into stores often too, but this does ensure that it does get fully up to temp almost every day..
So yeah I want to do that, because I will be letting it idle a lot no matter what BMW says, because it's freezing cold and it doesn't even have seat warmers, and I even want to add a remote start eventually..