|
||||||||
| Xoutpost server transfer and maintenance is occurring.... |
| Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
|
Speedometer packed ul
Cruise control still functions as normal. When I was slowing down say from 50 down to a junction that's when the range would drop and the fuel light would come on. The actual fuel gauge still reading as normal though. I scanned it with my C110 and it's saying there is no signal from both front abs sensors and the rear left abs sensor. Live data confirms that the only sensor giving a signal is the rear right. I have had a look through my old photos on the phone and there is also a screenshot of the C110 that says "09, 43, 50, 0F not found" and another that says "5B no message from steering angle control unit" - these are dated 29 September so I must have been looking for some reason. To add insult to injury the abs and traction lights are on but have been covered inside the cluster with black tape by a previous owner - but it's been like that for years with no problem. My main concern is getting the speedometer to work. I have consulted Chatgpt (don't laugh) and after much back and forth it's telling me to look at the rear left abs sensor or wiring. I'm not convinced about that. Can anyone shed any light on this? Thanks |
| Sponsored Links | |
|
|
|
|
#2
|
||||
|
||||
|
My speedometer quit about 4-5 years ago, and I used old-school methodology to restore functionality... I rapped it really hard with my knuckles.
My first car was a '56 Chevy, and I often had to hit the Motorola radio in order to get it to work (it was a tube radio, before solid state models were common). My guess is that at 210k miles, the plug-in at the rear of the cluster might've been loose or maybe the connection of the needle to the stepper motor needed a nudge, or whatever, but it worked thereafter. Probably not a solution in your case, but maybe??? Sent from my moto g power 5G - 2024 using Tapatalk
__________________
01 BMW X5 E53,3.0i-5L40E, 7/13/01 topas-blau,Leder-grau,"resto-project car" Here: 14 Lexus ES350,3.5L-U660E 09 HHR Panel,2.2L-4T45E 04 Chevy 2500HD,6.0L-4L80E 98 GMC Sierra 1500,5.7L-4L60E Gone: 66 Chevelle Malibu 2dr ht.,327>441c.i.-TH350>PGlide/transbrake 08 Cobalt Coupe,2.2L-4T45E 69 & 75 C10s,350c.i.-TH350 86 S10,2.8L-700R4 73 Volvo 142,2.0L-MT4 72 & 73 VW SuperBeetles,1.6l-MT4 64 VW,1.2l-MT4 67 Dodge Monaco 500 2dr ht.,383c.i.-A727 56 Chevy 210 4dr,265c.i.-PGlide |
|
#3
|
||||
|
||||
|
Step one - fix all the ABS sensors then assess what still not working.
The ABS, traction control, speedo and all trip computer functions (related to speed/distance) run off the ABS pulses. With three dead sensors, all bets are off as to what will work and what won't. ![]() BTW, it may be that the issue is not the actual wheel sensors failing - it could be the ABS unit itself - it has known faults with ABS sensor connections (internal to the ABS unit), giving faults that report as failed sensors.
__________________
Wayne 2005 BMW X5 3.0d (b 02/05) 2001 BMW F650GS Dakar (b 06/01) |
|
#4
|
||||
|
||||
|
I've read that speedo gets it's data from left rear. With tape over abs it's very likely v internal abs.
Sent from my iPhone using Tapatalk
__________________
2011 E70 • N55 (me) 2012 E70 • N63 (wife) |
|
#5
|
|||
|
|||
|
I've ordered a Bosch sensor for the rear to start off with. My next concern is actually getting the old one out - it hasn't been touched in 12years at least.
The tape over the lights I discovered last year when I went to repair the pixels. I had never tried to do that since I bought the car. Previously to that a few years before I had to replace the abs module as it failed and I lost all communication with it and the car was in limp mode. At the time I couldn't figure it out as obviously I had no lights on the dash. Last edited by Themoog; 11-19-2026 at 12:48 AM. |
|
#6
|
||||
|
||||
|
One of my very first repairs on my E53 was change of wheel bearing, which requires taking out the ABS sensor so you don’t break it, and the bolt snapped right off. turns out you can go six years without a bolt, as long as you wrap some Teflon tape around it to make it nice and snug when you put it back in.
Sent from my iPhone using Tapatalk
__________________
2011 E70 • N55 (me) 2012 E70 • N63 (wife) |
|
#7
|
|||
|
|||
|
Quote:
The sensor bolt on my E46 came right out tho, and that car was driven on salty winter roads before I got it. Maybe zap a little PB Blaster on it before you try to remove it?
__________________
2001 E53 M54 5MT Oxford green over crusty black leather 206,000mi 2002 E46 M54 2.5 5MT silver over black sensatec 217,000mi
|
|
#8
|
||||
|
||||
|
Most of mine (6 or so) came out just one broke. I'd recommend a firm hit with a hammer to shock the rust before turning. But: if it breaks you don't really need do drill out and replace
Sent from my iPhone using Tapatalk
__________________
2011 E70 • N55 (me) 2012 E70 • N63 (wife) |
|
#9
|
|||
|
|||
|
Of all aftermarket brands, I have had very good experience with Bremi.
About $28-$30/each. Just use realism.com to search for PNs, then search for Bremi.
__________________
1998 E39 528i 5sp MT 2006 E53 X5 3.0 6sp MT |
![]() |
| Bookmarks |
|
|
|
|