Vibrations when braking

[MarkingTime]

I purchased my 02 X 3.0 used and during the test drive didn’t really test the braking . After a few spirited driving sessions I noticed heavy vibrations when decelerating from speeds of 80-100mph range.

I’ve had the dealer and a local Midas (second opinion) check out the braking system. Although I have a ton of meat left on the pads and my rotors are well within spec, both agree that I need to replace both the pads and rotors in order to get rid of the vibrations.

The brakes on the vehicle I’m sure were never bedded nor was the vehicle driven by the pervious owner as spirited as drive.

QUSTIONS:
Is there anyway to resolve this issue without replacing both rotors and pads?

Thanks…

[Sudesh]

Discs and pads can cause this but also suspension lower arm bushes can be a problem also!!

[MarkingTime]

The dealer check both and determined it was the brakes.

[Sudesh]

If the rotors were replaced and not run in/bedded correctly then I would say YES the dealer is pretty much correct. The surface becomes abrasive and warped causing the problem.

[chubyball]

I think it's your pads problem, some brake pads doesn't handle at high speed and heat. Find out what pads do you have? Ceramic, organic, or metalic?

[khmer_x5]

I would try resurface your rotors first before spending a big chunk. good luck.

[iop9000]

warped rotors most likely

[The Cleaner]

Originally Posted by MarkingTime

The brakes on the vehicle I’m sure were never bedded nor was the vehicle driven by the pervious owner as spirited as drive.

QUSTIONS:
Is there anyway to resolve this issue without replacing both rotors and pads?

Thanks…

No need to bed in pads, that is an internet legend that simply will not die, I wish I could find ground Zero for that myth..... The proof that bedding is BS is in every new car. No new car manufacturer recommends or does “bed in’s” on new cars. If that was the case every factory would need a bedding in facility. I have spent a ton of time at the Toyota plant in Fremont California and I can tell you they do not have a bunch of people running around slamming on the brakes on new cars.

I have done at least 200 brake jobs and I have never bed in a job. With the exception of a couple jobs where the owner used junk parts I have never had one come back. I drive the car up to highway speed and check for vibration and squeak, that’s it.

Rant off, sorry

The solution is to replace the pads and rotors with OEM Jurid in the front and Textar in the rear. Use Balo or ATE rotors. Mount pads dry (non of that anti squeak orange or blue junk) and grease ONLY the tracks of the brake caliper frame.

Use dustless pads or no name rotors will have mixed results, the above formula will not have problems if done correctly.

Good Luck !

[JCL]

Originally Posted by The Cleaner

No need to bed in pads, that is an internet legend that simply will not die, I wish I could find ground Zero for that myth..... The proof that bedding is BS is in every new car. No new car manufacturer recommends or does “bed in’s” on new cars. If that was the case every factory would need a bedding in facility. I have spent a ton of time at the Toyota plant in Fremont California and I can tell you they do not have a bunch of people running around slamming on the brakes on new cars.

I have done at least 200 brake jobs and I have never bed in a job. With the exception of a couple jobs where the owner used junk parts I have never had one come back. I drive the car up to highway speed and check for vibration and squeak, that’s it.

Rant off, sorry

The solution is to replace the pads and rotors with OEM Jurid in the front and Textar in the rear. .....

I have to disagree here. I have done a lot of brake jobs as well, and I have found that bedding in is an important step. The degree to which it is required varies quite a bit with pad composition and rotor surface finish, but I consider it part of the brake job.

My experience with the Axxis Deluxe pads was that they required bedding in more so than many other pads, but that once it was done the pedal feel was equal to the OEM pads. That may have varied with my specific new rotors, as well, as that is the other half of the equation for the deposition of pad material on to the rotor surface.

Jurid is owned by Bendix. Bendix does recommend bedding in new pads, sometimes more stridently than other times. It depends entirely on the pad material. Bendix has also promoted new pad designs that include a metal strip on the pad surface, designed soley to reduce the bedding in time (their words).

Too many brake pad manufacturers (and the SAE) talk about the initial transfer of pad material to the rotor surface for me to discount it as a myth. I do think that it varies so much with pad composition that it is more of an issue with some pads than others. If I was a manufacturer I would specify a pad with less requirement in this regard, soley to reduce warranty claims for noisy brakes.

Jeff

[Quicksilver]

Maybe so but i gotta tell you the cleaner is right. No one at that toyota plant does this ( spent a few years there also) and no where will you find in the instructions for new car owners to do this, and finally i have never ever received these instructions when a brake job is done. A lot of scientific gobbley gook imho.

Originally Posted by JCL

I have to disagree here. I have done a lot of brake jobs as well, and I have found that bedding in is an important step. The degree to which it is required varies quite a bit with pad composition and rotor surface finish, but I consider it part of the brake job.

My experience with the Axxis Deluxe pads was that they required bedding in more so than many other pads, but that once it was done the pedal feel was equal to the OEM pads. That may have varied with my specific new rotors, as well, as that is the other half of the equation for the deposition of pad material on to the rotor surface.

Jurid is owned by Bendix. Bendix does recommend bedding in new pads, sometimes more stridently than other times. It depends entirely on the pad material. Bendix has also promoted new pad designs that include a metal strip on the pad surface, designed soley to reduce the bedding in time (their words).

Too many brake pad manufacturers (and the SAE) talk about the initial transfer of pad material to the rotor surface for me to discount it as a myth. I do think that it varies so much with pad composition that it is more of an issue with some pads than others. If I was a manufacturer I would specify a pad with less requirement in this regard, soley to reduce warranty claims for noisy brakes.

Jeff