WHOOOOAAAA!

[NyMench]

Intermediate Levers.....FYI

SI B 11 02 05
Engine January 2006
Technical Service

This Service Information bulletin supersedes S.I. B11 02 05 dated May 2005.

designates changes to this revision

SUBJECT
N62 Engine - Rough Idle, Misfire Faults after Cold Start


MODEL
E53 (X5 4.4 i/4.8is); E60, E63/64, E65/66 with N62 from 06/04 up to 02/05 production


SITUATION
Customer may complain of erratic engine idle speed lasting for approximately 20 seconds after a cold start. [COLOR=blue ! important][COLOR=blue ! important]Check [COLOR=blue ! important]Engine[/COLOR][/COLOR] Soon light may be illuminated and misfire faults for various cylinders (e.g. FC 2742, 2743, 2744, 2745, 2746, 2748, 2749, 274E) may be stored in the DME.[/COLOR]

CAUSE
Incorrect tolerances and geometry of Valvetronic intermediate levers are causing uneven cylinder filling during the transitional cold start period (60 seconds after the engine has been started) when the Valvetronic system is switching from the initial 6 mm to a minimum 0.3/0.8 mm valve lift.

CORRECTION
On a customer complaint basis, and after performing diagnostic procedure described below, replace the Valvetronic intermediate levers.

PROCEDURE

Perform basic engine diagnosis (compression, ignition, [COLOR=blue ! important][COLOR=blue ! important]fuel [COLOR=blue ! important]pressure[/COLOR][/COLOR], etc) to rule out other potential causes.[/COLOR]

Allow the engine to cool down.

Connect GT1/DIS loaded with CD 44.0, or higher, to a cold vehicle (coolant temperature below 30 deg C) and from the Function Selection select: "Service Functions", "Drive", "Engine management ME9", "Test runs" and then "Tolerance test, intermediate lever".

Start the engine and follow-up the test plan.

Observe rough running values when idle speed stabilizes. If values are in excess of +/- 2.5 accompanied with noticeable engine vibration (and sometimes Check Engine Soon flashing), then remove valve covers on both banks.

Look for the intermediate lever production date (stamped on the lever, next to the smaller roller contacting the eccentric shaft).

If the production date is in the range between "04 180" and "04 324" (e.g. day 324 of the year 2004), then the whole set of intermediate levers (16) has to be replaced. The same classification of levers must be used when ordering the intermediate levers (classification number is stamped below production date). There are 5 classifications of levers used in the N62 engine.

Note: In an individual cylinder head, all levers must have the same classification, but two different classification of intermediate levers may be used in one engine (e.g. bank 1: classification 2, bank 2: classification 3).

Important: The lower production range of the affected intermediate levers is only an approximation. It is possible that levers produced prior to "04 180" (but not earlier then "03 363") may have certain deviations in tolerances.

For Valvetronic intermediate lever replacement procedure, refer to RA 11 37 012 (bank 1) and RA 11 37 014 (bank 2), found in [COLOR=blue ! important][COLOR=blue ! important]BMW[/COLOR] TIS.[/COLOR]

IMPORTANT:

Improved intermediate levers are currently available from our Parts Department.

In the event of a reproducible customer complaint proceed with the diagnostic and repair procedure. There is no need to contact Technical Hotline.

PARTS INFORMATION
Part Number
Description
Quantity

11 37 7 516 895
Intermediate levers class 1
Maximum 16

11 37 7 514 012
Intermediate levers class 2
Maximum 16

11 37 7 514 013
Intermediate levers class 3
Maximum 16

11 37 7 514 014
Intermediate levers class 4
Maximum 16

11 37 7 514 015
Intermediate levers class 5
Maximum 16

11 12 7 513 194
Valve cover gasket bank 1
1

11 12 7 513 195
Valve cover gasket bank 2
1

11 31 7 507 432
Tensioner sealing ring
2

07 11 9 903 596
Valvetronic motor spacer ring
2

11 14 7 506 424
Timing chain cover, u-shape metal gasket, bank 1
1

11 14 7 506 425
Timing chain cover, u-shape metal gasket, bank 2
1

11 36 7 513 222
Vanos [COLOR=blue ! important][COLOR=blue ! important]solenoid[/COLOR] O-ring[/COLOR]
4

11 36 7 546 379
Vanos solenoid O-ring
4

11 36 7 501 423
Vanos unit bolts
4

[IMG]chrome://skype_ff_toolbar_win/content/cb_transparent_l.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/famfamfam/us.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/arrow.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG][IMG]chrome://skype_ff_toolbar_win/content/space.gif[/IMG]12 14 1 748 398[IMG]chrome://skype_ff_toolbar_win/content/cb_transparent_r.gif[/IMG]
Cam sensor o-rings
4

11 12 7 518 420
Eccentric shaft sensor o-ring
2

NOTE:

It is not necessary to replace spark plugs tubes during a course of this repair.

WARRANTY INFORMATION
Covered under the terms of the BMW [COLOR=blue ! important][COLOR=blue ! important]New [COLOR=blue ! important]Vehicle[/COLOR][/COLOR] Limited Warranty.[/COLOR]

Defect Code
11 37 91 42 00


Labor Operation:
Labor Allowance:


Main work:
00 55 453
93 FRU – E53 X5 4.4i/4.8is

91 FRU – E65/66

102 FRU – E60, E63/64


+Associated work:
00 55 793
91 FRU – E53 X5 4.4i/4.8is

[admranger]

TY NYMench.

Stupid question, but would this be covered under CPO also? The X5 that I am picking up tomorrow falls within these dates.

Was it widespread or some do and some don't?

Thanks!

[NyMench]

They should cover it......if it wasnot already performed on the car....ez to find out...and dealer has access to to what has been done under SB or warr work.....

even if the car is our of warr...i have seen dealers remedy the problem in good faith.....

Originally Posted by admranger

TY NYMench.

Stupid question, but would this be covered under CPO also? The X5 that I am picking up tomorrow falls within these dates.

Was it widespread or some do and some don't?

Thanks!

[JT///MC]

Originally Posted by NyMench

...i have seen dealers remedy the problem in good faith.....

:thum bup:

[NyMench]

jt///mc....

Wanna trade x5's i have a e36 m3 in the same color....and in all fairness....i think it would be better if you gave it to me....for coordination efforts!

[X5 Meister]

Hey NyMench, already posted that SIB in it's original format. If you want to delete your post and just link to mine feel free.
http://www.xoutpost.com/bmw-sav-foru...ld-days-2.html

Also, technically it's not covered under CPO since it's not mentioned in the SIB, but as stated above that doesn't mean they won't cover it.

[NyMench]

BLA BLA BLA BLA........ok

here is your star......

its all subjective to the dealer....anywho....

Just teasing you

Originally Posted by X5 Meister

Hey NyMench, already posted that SIB in it's original format. If you want to delete your post and just link to mine feel free.
http://www.xoutpost.com/bmw-sav-foru...ld-days-2.html

Also, technically it's not covered under CPO since it's not mentioned in the SIB, but as stated above that doesn't mean they won't cover it.

[X5 Meister]

Are you mocking me??? Where is that "ignore" function again???

[NyMench]

If the shoe fits!!!!!!!

Originally Posted by X5 Meister

Are you mocking me??? Where is that "ignore" function again???

[X5 Meister]

That's it!