|
||||||||
| Xoutpost server transfer and maintenance is occurring.... |
| Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
|
#1
|
|||
|
|||
|
Sorry for the delay, was away for the weekend.
Here's a few pics. |
|
#2
|
|||
|
|||
|
Quote:
I just had the factory trailer hitch installed and I'm searching all over to find out the factory pin-outs for the electric brake controller connections with no luck. I will use an aftermarket controller like yours and I just need the pin-outs of the BMW connector from the hitch wiring harness so I can connect the brake controller to the BMW connector. Any help would be greatly appreciated. Thanks, Jim |
|
#3
|
||||
|
||||
|
The thread below dates from the time of the E53, but does include attachments to the two DIY articles that are on this site. It may be helpful while you await the specific pin out information.
http://www.xoutpost.com/bmw-sav-foru...-do-i-buy.html
__________________
2007 X3 3.0si, 6 MT, Premium, White Retired: 2008 535i, 6 MT, M Sport, Premium, Space Grey 2003 X5 3.0 Steptronic, Premium, Titanium Silver 2002 325xi 5 MT, Steel Grey 2004 Z4 3.0 Premium, Sport, SMG, Maldives Blue |
|
#4
|
|||
|
|||
|
Brake Controller
Attached are the hitch and brake controller installation instructions. The information may help. In particular look at the table at the end of the hitch instructions. The hitch instructions are in two parts so the file size would be to large otherwise.
Chuck |
|
#5
|
|||
|
|||
|
Thanks folks, I really appreciate the help however I still cannot find a reference to the pinouts. I may endup using a circuit tester to find out. Here is what I'm looking for:
The wire colors and pinouts for the Tekonsha Prodigy controller are as follows: Black - Battery+ Red - Stoplight White - Ground Blue - Brake The BMW 4 pin connector wire colors that BMW provides as part of the hitch wiring for the brake controller are as follows: Red Yellow/red Yellow/green Brown I need to find out how those BMW wires map to the Tekonsha wires. I already have the Tekonsha Prodigy which is identical to the "factory BMW" controller. Thanks, Jim |
|
#6
|
|||
|
|||
|
Brake Controller
Hi,
I'm not sure what you mean by pin outs but the connection for the brake controller is in the back right cargo area. It's way at the bottom, and not that easy to find. Pull the cover off and look down towards the bottom, the wiring has to run from there up to the dash. I had my dealer install it, luckily there was a technician who had a boat trailer so he knew how to wire it. Good luck James |
|
#7
|
|||
|
|||
|
Has anyone tried a "wireless" controller? Sure looks easier. Plus, no holes in the dash
Prodigy Wireless Brake Controller by Tekonsha |
|
#8
|
|||
|
|||
|
Quote:
I've got the hitch on the X5 already, but I also plan to tow my camper with my Toyota Tacoma. While this is more expensive than just having a regular Prodigy controller (which I've already got too), it will certainly be cheaper than having a brake controller wired into the X5. That, and I don't have to worry about a mounting spot inside the X5 (or the Tacoma for that matter....) I'll then be able to just move the remote from vehicle to vehicle, depending on which one will be used to tow the camper.
__________________
Scott On Order: 2015 F15 X5 35i Space Gray with Mocha Nappa Interior Design Pkg and fineline Oak trim ZXD | ZCW | ZPP | 3AG | 456 | 4UB | 4U1 | 5DL | 688 To be Traded: 2010 E70 X5 35d Alpine White on Black with Dark Bamboo trim ZAP | ZCW | ZPP | ZPS | ZRC | ZTP | 322 | 328 | 330 | 386 | 4AZ | 4UB | 655 | 6FL | 6NF Last edited by scollins; 03-22-2011 at 09:29 PM. |
|
#9
|
|||
|
|||
|
Quote:
Hi guys, getting ready to install the prodigy (P2 model, carried over from my E53) controller. Is there any feedback on wiring - I have the same question as the user above. Looking to figure out where to mate the BLUE wire from the brake controller to the X5's 4 wire connecter... |
![]() |
| Bookmarks |
|
|
|
|