Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > Miscellaneous > Submit an Article
Arnott
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Closed Thread
 
LinkBack Thread Tools Display Modes
  #1  
Old 09-27-2010, 02:59 AM
Member
 
Join Date: Sep 2010
Location: Portland, OR
Posts: 13
championscooter is on a distinguished road
Change Transmission Fluid and Filter on X5 3.0i

Hi All,

I just replaced the transmission fluid and the filter on my 2001 BMW X5 3.0i which has 122K miles and never had ATF replaced. I’ve always hesitate to do it because BMW said it’s a “Lifetime Fluid”. But after seeing some people have done it, so I wanted to do my. The process it’s not too bad. I bought all my fluids and parts from www.pelicanparts.com . Make sure you use the SAME fluid said on the green label at the bottom of the transmission pan.

What you need:

6 Quarts of FUCHS Titan ATF 6000 SE ATF (P/N: 83 22 2 163 514)
1 Transmission filter kit (P/N: 24 11 7 557 069)
Oil manual pump to put the fresh ATF into the pan (see one of the pictures)
17mm socket (open the fill plug)
8mm Hex socket (open the drain plug)
Floor jack and Jack stands ( I used 2X6 studs)

If you only doing drain and fill, then you don’t need to remove the pan. For me at 122K miles, I went ahead replaced the filter kit also. Remember, you will only replace about 50% of the total ATF since the other 50% are up in the torque converter but that’s better than nothing.

First, you need to raise your SAV up. For me being small person 5’7”, 150lbs, I just needed 2-3 inch raise to work comfortably. I used two pieces of 2X6 studs (one about 24 inches and other 12inches), nailed them together with the short piece being on top flush on one end. The uneven end will act as a “ramp” for my SAV drive up onto and that gave me a total of 3 inches off the ground. You will need a total of 8 pieces of 2X6 to build for all four wheels. I found this is much SAFER for me going under the SAV than using the jacks. And a lot cheaper than have to purchase a floor jack and jack stands. Remember to pull your emergency brakes.

Make sure you’re able to loosing the fill plug first before drain the oil. The fill plug located on the Driver side just above the pan on the right. There is NO crush-washers on either one of them. There is NO hot exhaust pipe to worry about getting burn like the X5 4.4l. (See photo below)

Drain the oil first. The best time to drain is let the vehicle sit for hours or overnight for fluid settle down in the pan so you get most fluid drain. The drain plug uses TORX wrench (see below)

Now remove all 22 bolts around the bottom of the transmission pan. Be careful some fluids are still in the pan.

After the pan removed, pull down the filter using both hands. The filter holds in place by the O-rings and the base of the pan itself. There is no bolt or nuts holding the filter in place like some other vehicles. You will see there are “2 O-rings” attached to the nozzle. Make sure BOTH O-rings are removed with the old filter. Sometime one might stuck up inside. In that case, use the screwdriver to pry it out. And installing a new filter, make sure BOTH new O-rings are installed in the same manner. The new filter should come with 2 new O-rings. (See below photo). The purpose of O-rings is to provide tight seal to pump ATF fluid up into the torque convertor to lubricate the transmission gears. If not tight, gears may slipped.

Align the new filter in the same position as the old filter you had removed and PUSH up into the transmission.

Clean out the pan with degreaser to remove metal shaves accumulated at the bottom of the pan.

Install new pan gasket and lineup the pan. Hand snug each bolt until all 22 bolts on in place before torque them with the socket wrench.

Refilling new Transmission Fluids

I used the Sta-bil Quart manual pump (cost is $8.00) with clear hose to refill the ATF. With the engine shut off, put about 4 quarts of ATF (until a little bit start dribbling down the filler hole).

Hand tighten the filler plug and start the engine, once it reaches the operating temp shift through the gears slowly about 10 time or so. Make sure you have the emergency brake and brakes on while shifting since the car is still on the jacks or 2X6 studs like I do.

Now put the car in neutral with the engine running, loosen the filler plug and continue fill about another quart in until ATF start dribbling out the filler hole. Tighten the filler plug and torque it to 36lbft.

You are DONE!! It should takes approximately 5 ¼ quarts total. So buy 6 quarts should be plenty.

Good Luck!

More Related Resources:

http://blog.bavauto.com/bmw-tech-tips/bmw-automatic-transmission-fluid-filter-change-high-mileage

http://www.xoutpost.com/bmw-sav-forums/x5-e53-forum/35886-ok-i-did-transmission-fluid-flush-my-02-4-4i.html
Attached Images
          
Closed Thread

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 06:31 AM.
vBulletin, Copyright 2024, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.