Navigation V32 SIB
 

SIB 652102

http://www.bmwtis.net/images/homelogo.gifSI B65 21 02
Audio, Navigation, Monitors, Alarms, SRSJune 2008
Technical Servicehttp://www.bmwtis.net/tsb/bulletins/...mp/graybar.gif
This Service Information bulletin supersedes SI B65 21 02 dated March 2008.
http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif designates changes to this revision
SUBJECT
Navigation System Operating Software

MODEL
E38 (7 Series)
E39 (5 Series)
E46 (3 Series)
E53 (X5)
E83 (X3)
E85, E86 (Z4)
E65, E66 (7 Series)

INFORMATION
With the introduction of the navigation system operating software V32, there are currently 2 valid versions of navigation software:

1. Navigation system operating software V17.1 is used on MK III systems without the "split screen".
2. http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif Navigation system operating software V32 is used on MK I, MK II, MK III navigation systems with split screen, DVD-Top navigation systems (MK IV) on I-Bus vehicles and NAVI01, NAVI02, NAVI03 on E65/E66 vehicles.

CORRECTION
Navigation system operating software should be updated under the following circumstances:

• http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif There are no corrections or new data for the US market included.
• The navigation computer has been replaced.
• Progman prompts the navigation software to be updated during programming/coding.
• If instructed by a Service Information bulletin or the Regional Technical Engineer (RTE).

CORRECTIONS INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V31
NAVI03 and DVD-Top NAV system-improved software for:

• Reading dual layer DVDs
• Loading voice files

CORRECTIONS INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V30

• E65 and E66: Navigation system is inoperative after arrival at destination
• E65 and E66: Incorrect address book

http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif NEW FEATURES INTRODUCED WITH NAVIGATION SOFTWARE V32
No new features
FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V31 AND V30
No new features
FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V29
Destination input screen text changes:

• "State/Province" instead of "Country"
• "City/Postal Code" instead of "City/ZIP"
• "Town/City" instead of "City" (only in conjunction with road maps before 2006-2)

FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V28
E83, E85, and E86 - software fix for the following display/flap issues:

• Display turns back on after switching "Monitor off".
• Flap opens/closes by itself.
• Flap doesn't open.

FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V27
Only E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with the DVD-Top navigation system:

• Disclaimer screen disappears automatically after 8 seconds.
• City/Town names displayed in the map.

E46 (3 Series), E53 (X5), E83 (X3), E85 (Z4) with the DVD-Top navigation system;
E65, E66 (7 Series) DVD NAVI03 (from 03/05):
Destination input when "Country" (United States or Canada) is selected via:

• ZIP code (only for the United States)
• City name

Destination input when a US state or a Canadian province is selected via:

• Street name
• City name
• ZIP code (only for the United States)

Note - Only in conjunction with NAVTEQ DVD road Map 2006-2 or a more recent version:

• POI (Point of Interest) icons and "City center" icons are displayed together.
• Travel Information (TMC) is no longer displayed (is inactive and not selectable).
• Entries in "Address Book/Last Destination" displayed as:
  • City name, street name (destination entry via city name)
  • ZIP code, city name, street name (destination entry via ZIP code)
• Product information
• Legal disclaimer for usage of the navigation system and the data on the NAVTEQ road maps
• How to report missing or incorrect data feedback to NAVTEQ:

Website: www.navigation.com
Phone: 1-888-navteq9 (628-8379)
Email: [email protected]
FEATURES INTRODUCED WITH PRIOR NAVIGATION SOFTWARE V26

• The actual location is shown as an arrow in a circle.
• The destination is marked with a checkered flag.
• Map positioning in "travel direction" can now be selected in scales up to 100 mi.
• Disabled POI icons are now selectable on I-Bus DVD NAV systems in:
  • General Destinations
  • Travel Information
• The following functions are now selectable on the E65 and E66 with NAVI03 (from 03/2005):
  • Hide Map icons
  • General destinations and travel information

http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif After loading NAVI SW V32, the vehicle must be driven to ensure the proper functioning of the navigation system and the correct display of road number icons (e.g., interstate icons).
CHECKING THE SOFTWARE VERSION
MK I Systems
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as "1-1/80". The numbers have the following meanings: the first digit, 1, is a 1st generation navigation system (MK I); the second digit, 1, is a 1st device variant (top navigation – MK Ic color screen); the last two digits, 80, are the software version of the graphic component (8.0).
MK II Systems
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as "2-1/81". The numbers have the following meanings: the first digit, 2, is a 2nd generation navigation system (MK II); the second digit, 1, is a 1st device variant (top navigation – MK IIc color screen); the last two digits, 81, are the software version of the graphic component (8.1).
MK III Systems
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as "3-1/63" or "3-2/63" (MK III with split screen). The numbers have the following meanings: the first digit, 3, is a 3rd generation navigation system (MK III); the second digit, 1, is a 1st device variant (top navigation – MK IIIc color screen), or 2 is a 2nd device variant (radio navigation – MK IIIm monochrome display); the last two digits, 63, are the software version of the graphic component (6.3).
DVD-Top navigation system for I-Bus vehicles
The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as "4-1/00". The numbers have the following meanings: the first digit, 4, is a 4th generation navigation system (DVD); the second digit, 1, is a 1st device variant (top navigation – DVD color screen); the last two digits, 00, are the software version of the graphic component (10.0).
E65 and E66 Systems

• Enter the Service Mode of the Control Display.
• Select "MOST Devices".
• Scroll down and select "Navigation".
• Scroll down a few pages until "Software Version" is displayed.
• Software version for CD navigation (NAVI01) should be 7.3.2 (I-level E065-05-03-810.2).
• Software version for DVD navigation (NAVI02) should be 8.4.4 (I-level E065-05-03-800.2).
• http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif Software version for DVD navigation (NAVI03) should be E065-08-03-550 (SW 09.08.02).

Current Software Versions
Software version
Application
8.0
MK I - E39, E38 (up to 9/97)
8.1
MK II - E39, E38 (from 9/97), E46, X5
9.0
MK II - Radio Navigation – E52 (Z8)
5.1
MK III Radio Navigation – E52 (Z8) from 09/00
3.1*
MK III w/o Split Screen -E46 from 06/00, E39,E38 from 09/00, E53 from 10/00
6.3
MK III with Split Screen
10.0
DVD-Top Navigation
7.3.2
E65, E66 NAVI01 (CD-drive)
8.4.4
E65, E66 NAVI02 (DVD-drive)
http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif 09.08.02
E65, E66 NAVI03 (DVD-drive)
*Included in navigation software CD V17.1
LOADING SOFTWARE (ALL EXCEPT THE E65 AND E66)
For MK I, MK II, MK III, and DVD-Top NAV systems (except for the E65 and E66), use the following software loading instructions:

1. Turn the ignition to position 1 (terminal R).

Do not cycle the key or perform diagnosis while installing the new software. Make sure that the power supply is stable, i.e., do not switch on any electrical loads.

1. Activate "GPS-Navigation" and acknowledge the screen disclaimer by pushing the rotary knob on the board monitor.
2. Remove the map CD from the navigation computer by pressing the "Eject" button.
3. http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif Insert the navigation software CD (V17.1 P/N 01 59 9 789 299 index "x" for Mk III without the split screen; V32 P/N 01 59 0 141 891 index "y" for all other versions).
4. Mark I System (up to 9/97 production):

After a few seconds, the BMW roundel will appear on the board monitor and will be "filled in" clockwise to show the progress of loading (approx. 4-6 minutes).
Mark II System (from 9/97 production)
Mark III System (E46 from 06/00 and E38, E39, and E52 from 09/00 production)
DVD-Top navigation system (E46, E39, E52 from 09/02 and E53, E85 from 10/02 production):
After a few seconds, a menu of notes on the loading procedure and the "Progress" bar appear on the board monitor.
When the loading process has been completed, the message "Software has been successfully loaded" is displayed.

1. Remove the navigation system operating software CD and confirm the end of the loading process by pressing the rotary knob on the board monitor. "OK" appears in the display.
2. Drive the vehicle before delivering it to the customer to ensure that the navigation system is functioning and displaying (interstate icons) correctly.

LOADING SOFTWARE (E65 AND E66 ONLY)
http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif When programming any E65 or E66 using Progman V27.0 or higher, you will be prompted by the Progman screen that the "BMW navigation CD" must be loaded prior to programming the vehicle.
Note: Connect an approved battery charger before loading the software.

1. Turn the ignition on to Terminal R or 15.
2. Enter the navigation menu.
3. Remove the NAVTEQ road map CD/DVD.
4. http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif Insert the navigation operating software CD V32 (P/N 01 59 0 141 891 index "y") into the navigation computer and use the latest Progman version for NAVI03 (DVD navigation).
5. Select "Yes" with the controller to install the software.
6. The software will then load in two steps, taking approximately 10-15 minutes.
7. Do not touch the iDrive while the software is loading.
8. When the installation is finished, the CD will be ejected. The message "Installation Successful, Remove Software loading CD and press OK" will appear. At this point, select "OK" with the controller.
9. The navigation system will then "Reinitialize".
10. When prompted, insert the NAVTEQ road map CD/DVD.
11. Refer to SI B09 05 01 (Coding, Individualization and Programming) for any necessary coding and programming. Note that Progman will automatically reprogram all programmable control units that do not have the latest software.
12. Drive the vehicle before delivering it to the customer to ensure that the navigation system is functioning and displaying (interstate icons) correctly.

NAVIGATION COMPUTER REPLACEMENT - MK III AND DVD NAV
http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif When replacing a defective MK III or DVD NAV computer, a configuration signal is required to allow the new computer to load the correct software for its respective application. This is generated by using the SSS (Software Service Station) loaded with the latest Progman version, and the navigation system operating software CD V17.1 or V32.

1. Connect the Deutronic battery charger to the vehicle.
2. Connect the SSS via a diagnostic head or an O(P)PS (for D-CAN vehicles) to the vehicle.
3. Open a "New session" in Progman; select "Load SW" and follow the on-screen messages.
4. Select "Retrofits".
5. Select "Languages".
6. First select "Display" to select and/or check the correct languages.
7. Then select "Navigation" to select the languages for the NAV system.
8. At the prompt "Is the CD-ROM present?" select "Yes", but do not insert the navigation CD into the Nav Computer yet!
9. First select the main language and then an additional language (the choices are English, French, Italian, Spanish, and German).
10. NOTE: The gender of the announcer's voice (male or female) can no longer be selected.
    • MK I, MK II & MK III: Only male.
    • DVD-Top NAV, NAVI01, NAVI02 and NAVI03: Only female.
11. After activation of the automatic coding, the DIS tester tells you to follow the instructions on the monitor for navigation CD installation.
12. Place the navigation CD into the navigation computer CD drive.

Important: Do not switch the ignition OFF during the software loading procedure.

1. Once the loading has been completed, remove the CD and then confirm completion by pressing the rotary push button on the monitor.
2. Turn the ignition OFF for 10 seconds, and then turn it ON and conduct a functional check.
3. After this step has been finished, encode the navigation computer in the regular manner, using the path "1 Recoding".

TROUBLESHOOTING HINTS
The following problems may occur during the software loading procedure:

• The message "CD defective" appears on the display screen.
• The message "Fault during programming" appears on the display screen.
• The message "The system is restarting" appears on the display screen.
• The installation process has stopped; the display screen is blank; and the power LED on the navigation computer is off. The CD will not eject.

These complaints are usually the result of a faulty navigation operating software CD.

• For points 1-3 (error messages that appear on the display screen), check for the correct software version and try loading a new navigation CD.
• For a CD that will not eject from the navigation computer, follow the procedure below:
  1. Remove the navigation computer.
  2. Unplug the voltage supply (blue connector).
  3. Reconnect the voltage supply, and immediately press the eject button repeatedly until the CD in the drive is ejected.
  4. Insert a new navigation software CD and restart the installation process.

http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif PARTS INFORMATION
Part Number
Description
01 59 9 789 299
Navigation Software CD V17.1 Index "x"
01 59 0 141 891
Navigation Software CD V32 Index "y"
Copies of NAV SW CD V32 will be shipped to every BMW Center through the Automatic Tool Shipment Program.
WARRANTY INFORMATION
Updating the vehicle at the customer's request is not covered under warranty.

Interesting and complete informations.
Now we wait for a download link with V32 firmware.

Anyone has the link for the V32 software download?

Summary of software versions included on V32:

NO CHANGE to the following nav units:
Mk1 v8.0
Mk2 v8.1
Mk3 v6.3 (3-1/63)
Mk4 v10.0 (4-1/00)
NAVI01 v7.3.2
NAVI02 v8.4.4

This nav unit is updated:
NAVI03 v09.08.02

waiting for links

SOS for Mk4

As we see this soft is usefull to the NAVI03 navi units only. There is no anything new for all other devices.....

I purchased NAV OS V32 from the BMW dealership but there's no change for my NAV Unit. If anyone wants it, i'll sell for $20.00 including S&H. Send payment to my paypal ID [email protected]. I will ship as soon as the payment is received.
Thanks.

Nav V32
 

Hi, could please anyone let me know how can I get the upgrade file.
exept for torrent!!!) Has anyone got the direct link?
Thanks
what is the correct file size?:stickpoke

See here:
-> http://www.xoutpost.com/navigation-sy...mac-toast.html

or

-> http://www.bmwportal.net

;)

Thanx, I installed it. I have read that in higher versions of the software one can change the view to angle view and also the scalew can be set to 100feet. I did not find these two settings. If anyone can give me update on it I would be very greateful. Thanks.
huli76it is possible

what software version does V32 show on a MKIV in the settings menu?

I Have MKIII unit. When i will do the update will let me choose between these two options (V17.1 and V32P)?

Also. V17.1P is for me? I read that V25 is the latest. Do i say something stupid?

What do you mean MKIII without split screen? There are MKIII with split screen? If yes how can i know which of the two i have?

You should use any OS disk of Ver. 22 OR higher to get to 3-1/63. You will need the key CD also if you are currently at 3-1/30 or below. You will be able to have split screen if you want it.

Yeah OK. But i don't get the above insrtuctions that i quote. If i want split screen what i do?

When i will do the update what option do i choose? V17.1P or V32P?

IIRC you load any OS disk 22 to 32 and it will ask for the Key. Load the key and you are finished. Go to the settings screen and select split or full screen.

What IIRC means? Where do i find the key?

If I remember correctly. If the key is not on xoutpost.com then try e38.org

I have 3-1/63 and MKIII Unit so i dont need the key cause i am above 3-1/60. Right? But if i buy a MKIV will i need the key? Also...i can't find the key...i searched but nothing.

3-1/63 is as far up as you can go with MKIII. MKIII is the only one which ever needed the key. MKIV will go to 4-1/100 with Ver. 31.

I'm looking at biting the bullet and upgrading my MKIII to a MKIV, most likely bought off Ebay. Reading through this the SIB says:

NAVIGATION COMPUTER REPLACEMENT - MK III AND DVD NAV
http://www.bmwtis.net/tsb/bulletins/...c_temp/new.gif When replacing a defective MK III or DVD NAV computer, a configuration signal is required to allow the new computer to load the correct software for its respective application. This is generated by using the SSS (Software Service Station) loaded with the latest Progman version, and the navigation system operating software CD V17.1 or V32.

1. Connect the Deutronic battery charger to the vehicle.
2. Connect the SSS via a diagnostic head or an O(P)PS (for D-CAN vehicles) to the vehicle.
3. Open a "New session" in Progman; select "Load SW" and follow the on-screen messages.
4. Select "Retrofits".
5. Select "Languages".
6. First select "Display" to select and/or check the correct languages.
7. Then select "Navigation" to select the languages for the NAV system.
8. At the prompt "Is the CD-ROM present?" select "Yes", but do not insert the navigation CD into the Nav Computer yet!
9. First select the main language and then an additional language (the choices are English, French, Italian, Spanish, and German).
10. NOTE: The gender of the announcer's voice (male or female) can no longer be selected.
    • MK I, MK II & MK III: Only male.
    • DVD-Top NAV, NAVI01, NAVI02 and NAVI03: Only female.
11. After activation of the automatic coding, the DIS tester tells you to follow the instructions on the monitor for navigation CD installation.
12. Place the navigation CD into the navigation computer CD drive.

I thought having read a few retrofit guides that it was simply plug and play between the two, but the above seems to suggest that the MKIV needs to be coded to the car. So my question is do I need to get it coded, or is the above in reference to a brand new unit without software loaded?

If you purchase brand new, then the OS needs to be loaded and the unit coded as per the BMW instructions

If you purchase 2nd hand, then an OS will already be loaded and the nav likely to be coded for the prior vehicle.

Coding doesn't make such a huge practical difference, but you may find the nav may not properly be coded for your radio module. Also, it may not have the languages you want. In this case, my NavCoder software will code it for you.

can someone help me get v32 on my MKIV system.
I would pay for the file upgrade or if someone wanted to email the file, Please help johnnybel

http://www.xoutpost.com/508030-post1.html

You can make your payment for the development of this forum!:thumbup:

OK, I just bought a 2006 X5. LOVE IT! I got to the "setting" screen and in the upper right I have the following; 4-1/71 so my question(s) are;
1. Which Nav system do I have
2. Is there a new Operating System I should be installing

My Nav disk is; 2009.1.65 90 2 147 669

New to this so any advice is appreciated.
ken

You have a MKIV unit running Ver. 27.1. You should update to Ver.32 to be at 4-1/00 (4-1/100). This forum tells you how to do it. You can download Ver.32 or you can buy the disk from the dealer for less than $10. P/N 01 59 0 141 891.

Burning V32
 

Do I burn this on a normal DVD-r 4.7GB disk or is there something special I need to do?
Thanks,
Ken

Gettting 6 flashes
 

I burnt this file on a DVD-R then a regular CD and all I get is the unit flashing about 6 LED blinks and dont seem to be updating. Am I doing something wrong?
ken

Before you start messing with it, you should do some reading to avoid future problems. Just my 2 cents.

http://www.xoutpost.com/articles/all...ystem-faq.html

http://www.xoutpost.com/electronics/...rt-number.html

Read it all. However it does not tell you what type of CD to burn it on (DVD-R, DVD+R, CD) do you need to make the disk bootable, etc. Lacking instructions don't help newbees like myself. I downloaded the V32 build which has a LOT of folders in it but I am not sure if I am to make a disk from this entire image. I've followed the installation instructions to the "T" but this build just wont load. I got a feeling its the way I am burning the disk.
ken

Go to the dealer and buy the disk. It retails for $8.67. P/N 01 59 0 141 891

Burn the ISO to DVD-r single layer. Do not extract anything

Hello there!

Does anybody knows if NAV OS V32 works for a Mini cooper 2009? I want to update my OS and maps.... Right now i have the follow data in my cdrom.toc file:
Continental Automotive GmbH
Content
Volume: CD_6607
Date: 10.10.2008
db: mex(2008Q1)
Area: Mexico & Puerto Rico
Supplier: Teleatlas
Version: 505.95.859.8.84
Customer: 318766610
Features: ZIP3kb feaB6(BMW) pti(BMW)
TPD: 2008090007
SVD: no
TMC: no
Phoneme: no
DBAL: V1.15V2.13V3.0V4.8V5.6V6.1V7.1
I’ll very appreciate any help.
Arturo

If your car has the iDrive controller, then NO.
OS update is only via the dealer via the diagnostic system

Maps can be updated easily by replacing the map disc

Thanks Jochen! I'll go with my dealer.....