Forum: X5 (E53) Forum
05-08-2019, 09:11 PM
|
Replies: 3
Views: 2,305
Coding DME and EWS
Knowing what you know about coding, and the fact that my E53 won't start, how would or should I go about testing or coding?
My cable is essentially a K cable, pins 7/8 are jumpered, and it does...
|
Forum: X5 (E53) Forum
05-08-2019, 07:53 PM
|
Replies: 3
Views: 2,305
What software/cable for E53 series coding?
I have rheingold and a USB-ODBII cable, but can't do any programming, or re-coding.
Can someone who actually has done it please tell me what I need, be it ICOM, or whatever? I think I have a...
|
Forum: X5 (E53) Forum
05-07-2019, 01:36 PM
|
Replies: 16
Views: 3,217
Checked the ignition switch
Watched a YouTube video on it - with a multimeter, I confirmed voltage is being supplied to the starter, checked the fuses for the immobilizer, also good. I guess next step is to check the voltage...
|
Forum: X5 (E53) Forum
05-05-2019, 11:31 PM
|
Replies: 16
Views: 3,217
EWS or Relay
The battery has been on charge the entire time. The relay 'clicks' when you turn it over, but the starter doesn't engage, nor do I hear the fuel pump - but this is brand new.
However - before,...
|
Forum: X5 (E53) Forum
05-05-2019, 02:16 PM
|
Replies: 16
Views: 3,217
And today - no crank, no start?! JFC
So today I was prepping for a road test, but the ECM and a couple of relays back in the holder, but the air cowl back in place with the 4 plastic rivets, went to Fire it up - nothing, no fuel pump...
|
Forum: X5 (E53) Forum
05-03-2019, 11:06 PM
|
Replies: 16
Views: 3,217
|
Forum: X5 (E53) Forum
05-03-2019, 08:24 PM
|
Replies: 8
Views: 1,934
|
Forum: X5 (E53) Forum
05-03-2019, 08:22 PM
|
Replies: 16
Views: 3,217
|
Forum: X5 (E53) Forum
05-03-2019, 02:11 PM
|
Replies: 16
Views: 3,217
What cable to use for E series?
I have a USB to ODBII cable, that has the two pins jumpered, but I don't have an ICOM cable - from what I've read you need to have ICOM to do any programming with an E series, if that is correct...
|
Forum: X5 (E53) Forum
05-03-2019, 01:03 PM
|
Replies: 16
Views: 3,217
Codes and Software
The MAF and TB are both 3rd party, from BAV Auto (just before they shut down)
I was using DIS, but then migrated to Rheingold, but the laptop is so old that it was painful.
I now have a newer...
|
Forum: X5 (E53) Forum
05-01-2019, 10:41 PM
|
Replies: 16
Views: 3,217
working on it
Making a smoke machine based on this - https://www.youtube.com/watch?v=L9CDZ9lu6Rs&t=387s
we will see what we see when I'm ready to test tomorrow.
|
Forum: X5 (E53) Forum
04-25-2019, 03:12 PM
|
Replies: 16
Views: 3,217
2002 E53 4.4i - rough idle, surging power.
Original codes pointed to MAF and Throttle Body - replaced both, no difference. Replaced fuel pump, still no good.
I am not getting any codes other than MAF and TB, I have checked for continuity...
|
Forum: X5 (E53) Forum
03-17-2019, 06:28 PM
|
Replies: 18
Views: 5,503
still out of commission
I have ITSA/D and /P - I have been all thru it, and reset TB adaptions, I only have the following faults
115 signal hot film air mass flow sensor (it's disconnected right now)
134 - learning...
|
Forum: X5 (E53) Forum
03-09-2019, 01:21 AM
|
Replies: 7
Views: 829
That looks complicated as all get out
But - if I can program my throttle body, I'll give it shot - was hoping for something easier, lol.
Thank you for the link, that is a very well written document.
|
Forum: X5 (E53) Forum
03-08-2019, 11:53 PM
|
Replies: 7
Views: 829
Any thoughts on the Foxwell 520 scanner?
I think I need to do my throttle body adaptations, and as my DIS seems to be crappy, I was considering buying one of these with BMW software installed.
https://tinyurl.com/y2lldcmm
thank you
|
Forum: X5 (E53) Forum
03-08-2019, 08:39 PM
|
Replies: 7
Views: 829
This is for INPA only
Not for DIS - and doesn't address the error on pin 17 I'm getting...
Now, I'm not sold on DIS, it's very old, and clunky. If there is something I can buy that you can recommend, I'm stuck trying...
|
Forum: X5 (E53) Forum
03-08-2019, 11:33 AM
|
Replies: 7
Views: 829
DIS run in a VM, PIN 17 error?
When using my DIS (from ebay a number of years ago) and an ODBII to USB cable, I can't run any Diagnostic Test Schedules. Every time I do, I get:
Control unit selected has not been Found!
Note:...
|
Forum: X5 (E53) Forum
03-02-2019, 01:02 AM
|
Replies: 18
Views: 5,503
Pedal pin outs
I will be testing this tomorrow to see if I have continuity and voltage across the pins of the pedal, but I have a question:
There are two vac lines coming from the corrugated tube to the throttle...
|
Forum: X5 (E53) Forum
03-01-2019, 08:43 PM
|
Replies: 18
Views: 5,503
|
Forum: X5 (E53) Forum
02-24-2019, 01:48 PM
|
Replies: 18
Views: 5,503
|
Forum: X5 (E53) Forum
02-16-2019, 11:18 PM
|
Replies: 214
Views: 38,869
|
Forum: X5 (E53) Forum
02-16-2019, 09:44 PM
|
Replies: 18
Views: 5,503
The Butterfly wasn't moving even with the...
The Butterfly wasn't moving even with the accelerator, so we pulled it, cleaned it, and then even after replacement, didn't move - so we tested moving it, and the revs did increase.
|
Forum: X5 (E53) Forum
02-16-2019, 04:23 PM
|
Replies: 18
Views: 5,503
02 4.4 E53 Throttle body error codes
Hi all,
Driving up a hill, 70mph, suddenly 'ding' - engine failsafe mode, and lurching power. So I pull over, shut down - wait a minute, start again, drove ok for the next 30 minutes.
Later...
|
Forum: X3 (E83) Forum
11-16-2016, 06:49 PM
|
Replies: 5
Views: 2,295
Video is private?
Please can you make public? I'm trying to adapt my useless flashlight into a cigarette lighter socket, for use as a USB receptacle. Not sure which PIN should be positive, etc.
|
Forum: X5 (E53) Forum
08-26-2016, 08:51 PM
|
Replies: 2
Views: 858
Found it - never mine
64218409066
RealOEM.com - Online BMW Parts Catalog (http://www.realoem.com/bmw/enUS/showparts?id=FB33-USA-11-2001-E53-BMW-X5_44i&diagId=64_1064)
|