Xoutpost.com

Xoutpost.com (https://xoutpost.com/forums.php)
-   X5 (E53) Forum (https://xoutpost.com/bmw-sav-forums/x5-e53-forum/)
-   -   Help needed Exhaust manifold (https://xoutpost.com/bmw-sav-forums/x5-e53-forum/113310-help-needed-exhaust-manifold.html)

X5E53John 06-03-2021 01:19 PM

Help needed Exhaust manifold
 
Hi all ive just come to the conclusion that my catalytic converter is rattling and on its way out
Ive been looking at how hard it is to remove the catalytic converters to replace them
Does anyone have any experience with this they can shate please


Sent from my iPhone using Xoutpost.com

Effduration 06-03-2021 01:54 PM

Which X5 do you have ? It's different for 6 cyl, 8 cyl and diesel. Also is your call left or right-hand drive?

Is Essex in the UK?

X5E53John 06-03-2021 02:40 PM

Quote:

Originally Posted by Effduration (Post 1204604)
Which X5 do you have ? It's different for 6 cyl, 8 cyl and diesel. Also is your call left or right-hand drive?

Is Essex in the UK?



Hi sorry i forgot to give the details i was stressing out
Its the E53 X5
3.0 petrol the M54 engine
And its a right hand drive
Yeah Essex is the uk
Thanks in advance


Sent from my iPhone using Xoutpost.com

Effduration 06-03-2021 02:49 PM

I suggest you modify your signature to Essex, UK

You'll have to have a look, but I am not sure how RHD steering hardware interferes with exhaust manifold (if at all).

But there is pretty good room in an X5. People are often able to get the exhaust manifolds off with a variety of wobble adapters, extensions, universal adapters, etc. Attack from above and below. Be prepared to remove fender liner, etc. if needed.

X5E53John 06-03-2021 03:37 PM

Ok i will look in to changing that,
Have you taken a manifold off of one of these before?
It looks like the steering column may pose a problem it just looks really tight for space to bring it down and out past the subframe etc



Sent from my iPhone using Xoutpost.com

Effduration 06-03-2021 03:46 PM

I have not taken off an exhaust on a RHD car

I have removed exhausts from several LHD X5's but pulled them with the cylinder head as part of a head gasket job...I then removed them from the head. This is not what you are talking about.

I have read reports of many people who have removed them while engine and head is in place . It is quite fiddly, but can be done as I described.

Henrym3 06-03-2021 03:55 PM

https://www.newtis.info/tisv2/a/en/e...nifold/ASfqPL8
Not sure if this link will work


Sent from my iPad using Xoutpost.com

Henrym3 06-03-2021 03:57 PM

Try thIs


Remove centre silencer.
Remove reinforcement plate.
Attention!
The job item "Removing and installing bracing plate" contains important installation notes.
Protect anti-roll bar from paintwork damage.

Remove the retaining bracket and rubber mount from the anti-roll bar.
Release anti-roll bar link on the left and right from the anti-roll bar.

Note:
The oxygen sensors risk being damaged when the exhaust manifolds are removed and installed.

Remove both front oxygen sensors.

Remove cover for fuel injectors.
Note:
Do not mix up the monitoring oxygen sensor for cylinders 1 to 3 and 4 to 6 on the plug connection to the wiring harness.
Mark plug connections.
Unclip the cable from the holder. Disconnect plug connection. Unclip cable on rear side of engine from cable routing.

Remove monitoring oxygen sensors.

Note:
The rear exhaust manifold with catalytic converter is possible only after removal of the front exhaust manifold with catalytic converter.

Remove front exhaust manifold with catalytic converter.
Remove rear exhaust manifold with catalytic converter.
Installation note:
Clean sealing surfaces, replace gasket.
Coat threads with CRC copper paste.
Replace nuts.


Sent from my iPad using Xoutpost.com

X5E53John 06-03-2021 04:02 PM

Quote:

Originally Posted by Henrym3 (Post 1204619)
Try thIs


Remove centre silencer.
Remove reinforcement plate.
Attention!
The job item "Removing and installing bracing plate" contains important installation notes.
Protect anti-roll bar from paintwork damage.

Remove the retaining bracket and rubber mount from the anti-roll bar.
Release anti-roll bar link on the left and right from the anti-roll bar.

Note:
The oxygen sensors risk being damaged when the exhaust manifolds are removed and installed.

Remove both front oxygen sensors.

Remove cover for fuel injectors.
Note:
Do not mix up the monitoring oxygen sensor for cylinders 1 to 3 and 4 to 6 on the plug connection to the wiring harness.
Mark plug connections.
Unclip the cable from the holder. Disconnect plug connection. Unclip cable on rear side of engine from cable routing.

Remove monitoring oxygen sensors.

Note:
The rear exhaust manifold with catalytic converter is possible only after removal of the front exhaust manifold with catalytic converter.

Remove front exhaust manifold with catalytic converter.
Remove rear exhaust manifold with catalytic converter.
Installation note:
Clean sealing surfaces, replace gasket.
Coat threads with CRC copper paste.
Replace nuts.


Sent from my iPad using Xoutpost.com



Thank-you the link didn’t work but i assume this is the copied version from the link.
Im a bit unsure why i would have to remove the cover for the fuel injectors though?
By the sounds of this once all the bolts are removed and everything unplugged etc it shouldn’t be too much hassle to wiggle the manifold down and out


Sent from my iPhone using Xoutpost.com

Henrym3 06-03-2021 04:14 PM

It’s probably 10 years since I did this job to my sons e53 I don’t remember the exact details other than it being a complete pita Those manifolds just don’t want to come out. Some of the bolts are difficult to get at and need care and lots of wd40 plus time for it to penetrate. Not a quick Saturday afternoon job. Sorry I can’t help with the injector question, I just don’t remember. Yes, that is the info from TIS.


Sent from my iPad using Xoutpost.com


All times are GMT -4. The time now is 06:32 AM.

vBulletin, Copyright 2024, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved.