OBDII O2 Sensor Not Ready
 

My 2005 X5 (E53) failed SMOG test recently with O2 sensor not ready. Although I had a battery change, that was over 3,000 miles ago. I've performed the drive cycle four times (using various procedures found on the Internet). I'm starting to suspect bad O2 sensors. However, there's no check engine light.

By using a OBDII scanner, I got the oxygen sensor data. Can someone tell me whether I have bad sensors by looking at the data (see attached screen shot)?

Can you graph your O2 sensors live data? Usually you will get codes within a few drive cycles if they aren't performing properly.

Another member was recently hung the same problem and replacement sensors was the fix.

I have one post cat sensor that is reading rich all the time while the pre cat is fine so I suspect early demise. I will swap the connectors to see if the rich reading sensor swaps banks then reeplace if it does.

If you do any form of reset codes the smog monitors start over from scratch.

I just went through something similar:

https://xoutpost.com/bmw-sav-forums/...ncomplete.html

Mine was the O2 sensor *heater* readiness monitor being incomplete. Is that what yours is? I believe that is the one that takes the longest to complete under normal driving, even when everything is perfect.

I did replace the rear, original O2 sensors (and had replaced the front ones 30k miles earlier), and then waited about 200 miles of regular driving for the monitor to show as ready. But I am not sure at all that I needed to replace the sensors. I tested resistance of the heater elements in those sensors and they were normal, but I ran out of options and patience and did the replacement.

You should be able to check those readiness monitors on your OBD2 reader, unless it is a really low-end model. So that would at least take any mystery out of the smog check. No need to go there again until your reader is showing no codes and all monitors ready. And once you've got that, you should be sure to pass unless you fail the visual inspection.

Possibly ironic; the emissions monitor is useless in the BMW sub menu on the foxwell but the basic obd sub menu works perfectly to check you are good to go before you leave for testing.

not a BMW, but the GM drive cycle crap tested my patience
 

Good luck getting your vehicle ready for emissions testing; it may test your patience, as it did for one of my vehicles.

I have always scanned my vehicles for "monitor readiness" (on my old Innova 3100i scan-tool for many years; previously I had done a pre-test scan with a Snap-On scanner at a friend's shop, ever since 1998), prior to going to the inspection station. The Innova tool has three readiness lights: red, yellow, and green. "Green" means OK.

I now have a Foxwell NT 510 Elite, with BMW and GM programming; I haven't tried using it for emissions readiness tests yet, but I hope it'll help pinpoint exact details that may help me for future readiness testing, with no long drive cycle periods necessary.

If the car showed not ready, or had a fault cleared, I'd have to follow a series of General Motors "Drive Cycles"
(all of my vehicles post-OBD2 inception have been GM, until I got the X5 recently), until the monitors all went green. Sometimes, it was a long process.

Most recently, at least in the last five or so years, I had to do drive cycles on three vehicles:

• 1) '98 GMC 1500 after clearing misfire and oxygen sensor faults, because the wife hadn't told me about them until after the inspection was already overdue; after the repairs on day one, I drove the truck about 50 miles before it was ready,
  
  
• 2) '04 Chevy 2500HD after not driving it for two months, and again, at the last minute, replaced another oxygen sensor, cleared the fault, and drove it 30 miles to go "green" on the monitors, and stopped by the inspection station on the way home (not bad!), and
  
  
• 3) '09 HHR Panel, which I had been using as my daily driver on my 120+ mile-per-day commute to work, but parked it a month before retirement because it suddenly needed several repairs (brake pads, wheel sensors, VVT actuator, MAF sensor, Evap system faults) that I had put off while working/commuting 16 hours a day for the previous three months; after I parked it, then retired, I finally needed it again a year later, so I began the repairs.
  I fixed the first four items in a short time, cleared codes, and was driving the cycle before another hard evap code appeared. I replaced the evap canister vent valve, blew out the lines, and cleared the codes again. Since the inspection/registration had expired during the inactive year it sat parked, I got a temporary 10-day permit for driving the test cycle. I'm glad it was a 10-day permit, because I drove 15 cycles, and almost 400 miles, before it finally showed ready for inspection. It's never had another fault in the five years since then; I've no idea why it wouldn't reset.

Use the generic module on foxwell it lists all the monitors in one place. Very easy. Evap can show not ready and pass in most states even though the guys at the testing stations won't believe you until you go do the test and the printout shows pass with evap not ready.

Texas allows one "not ready"; YMMV in other states
 

I think that I have had one "not ready" on each pickup over the years, and they passed (I had been busy, and skipped pre-testing on the 2500HD one time, since there were no faults, and the wife drove her GMC to the station without me knowing of it).

Some states allow no free passes, and others two. And, some locales don't test at all (lucky bastards!).

I forgot to mention that the evap is also not ready but since I'm in California, SMOG shops will pass it with one monitor not ready. So I just need to focus on the O2 monitor.

OBDII Bluetooth scanner:
https://smile.amazon.com/gp/product/B07CP5ZJVQ/

Scanner app:
https://play.google.com/store/apps/d...ovz.carscanner

That setup should allow watching real-time O2 values. Depends on the app if it will show monitor readiness

I'm not sure. Thanks for the suggestion...I will try. This is the app I'm using:
https://play.google.com/store/apps/d...ovz.carscanner