The mudflaps with the flares look stupid, but thats just my opinion lol.

:thumbup: Has anyone bought the parts and can comment on the pricing? Going to call my SA in the morning to get a general breakdown and place the order. Going with Lemans Kit! Very nice write up.

3.0/4.4 – Aluminum Running Boards WITH Front Flares and 4.8 Style Rear Flares.

NOTE 1: Must buy RB Retrofit Kit (51710017315). Also, get the additional parts below which will REPLACE the wheel arches in the RB Retrofit Kit with FLARES.
NOTE 2: If you already have RBs, then you ONLY need the the parts listed below and 26 Blind rivets (51717002953).
NOTE 3: The Front and Rear Flares are DIFFERENT for vehicles with or without RBs.

Part Number ------ Description ------------------------- QTY
51 11 7 073 517 -- MOUNTING PARTS SET (REAR SUPPORTS) -- 1
51 12 7 046 919 -- REAR SUPPORT BUMPER TRIM, LEFT------- 1
51 12 7 046 920 -- REAR SUPPORT BUMPER TRIM, RIGHT------ 1
51 71 7 051 035 -- FLARED WHEEL ARCH, REAR LEFT -------- 1
51 71 7 051 036 -- FLARED WHEEL ARCH, REAR RIGHT ------- 1
51 71 7 051 037 -- FLARED WHEEL ARCH, FRONT LEFT ------- 1
51 71 7 051 038 -- FLARED WHEEL ARCH, FRONT RIGHT ------ 1 So would have to go with this set....What would be the cost for this set? sorry for asking.

I've been researching this topic for weeks and finally came across this thread. Amazing write up. There are so many but this was very thorough.
Has anyone answered the cost question?

3.0/4.4 – Aluminum Running Boards WITH Front Flares and 4.8 Style Rear Flares.

NOTE 1: Must buy RB Retrofit Kit (51710017315). Also, get the additional parts below which will REPLACE the wheel arches in the RB Retrofit Kit with FLARES.
NOTE 2: If you already have RBs, then you ONLY need the the parts listed below and 26 Blind rivets (51717002953).
NOTE 3: The Front and Rear Flares are DIFFERENT for vehicles with or without RBs.

Part Number ------ Description ------------------------- QTY
51 11 7 073 517 -- MOUNTING PARTS SET (REAR SUPPORTS) -- 1
51 12 7 046 919 -- REAR SUPPORT BUMPER TRIM, LEFT------- 1
51 12 7 046 920 -- REAR SUPPORT BUMPER TRIM, RIGHT------ 1
51 71 7 051 035 -- FLARED WHEEL ARCH, REAR LEFT -------- 1
51 71 7 051 036 -- FLARED WHEEL ARCH, REAR RIGHT ------- 1
51 71 7 051 037 -- FLARED WHEEL ARCH, FRONT LEFT ------- 1
51 71 7 051 038 -- FLARED WHEEL ARCH, FRONT RIGHT ------ 1

I know this is a very old thread (sorry for the revival), but i just purchased the Retrofit Kit from ECS and was wondering if there was an install guide out there. All the links to past DIYs are stale. If you have a PDF or detailed write up please PM me. Thank in advance!:thumbup:

Alec

No need to feel bad. That's what the information is for - to help people.

Updated links to the Retrofit Kit and the Lemans install kit too. :thumbup:

Got the Fenders today and plan on doing the procedure tonight. What tools are necessary?

I know i need a Drummel Tool, Screwdriver(s), Small 'prying' tool and hammer..what else though?

Thanks guys!!:thumbup:

IIRC, I used wire cutters to remove the old rivets. Just work the blades underneath and snip. You didn't list the rivet gun so I hope you have one of those.

Other than that, you should be all set. Just take your time and you shouldn't have any problems.

Good luck! :thumbup:

EDIT: I found one of my old posts with some tips.

http://www.xoutpost.com/582486-post2.html

Like Popa said.. if not send me round trip ticket...I get them bad boys install for you.
Note: If you don't have rivet gun... Just use two needle pliers.:thumbup:

Old thread but just a heads up the kit 51-71-0-017-315 is no longer available. I think all the parts can still be purchased separately but realoem says these will cost an arm and a leg. Around $2400 not counting the hardware. Even with a nice discount this will still be very costly. If all goes as planned I'll have my first E53 in about a month and sure would like to install these. Kinda bummed.