Rear exhaust tailpipes 3.0d sport
 

Hi all

have any of you put tailpipes on your 3.0d (the ones that come out of the bumper)

the aftermarket exhausts seem expensive just to get the look of the 4.8

thanks in advance

no but i am seriously considering it, when you read and see all the stuff people do to free up the system on petrol 4 cylinder japanese turbo cars, you would think that there might be some gains from doing it to the 3.0d

there are a couple of clips on youtube of people who have, but i'm not sure if they did it for power or noise.

keep us posted on what you decide

What do you want to do?Just fit tailpipes on your existing silencers just for looks (dummies),or do you want to modify your standard silencers to make them work with a straight through design?If you want this ,you will need t remap your car for less back pressure.
You have threads here with both,just search 3.0D silencers.
The ones you see on tube that sound "loud and nice" basically have no rear silencers ,its a straight through design but are obviously mapped ,for such.

Hi

i want the exhausts to come out of the bumper and be connected to the existing system (and work)

the car was remapped before i bought it so would it need to be done again

regards

if you want to just put tips on you dont need to remap anything..there just for show.. heres 2 links i found in like 5sec on ebay


BMW X5 3.0 Polished Exhaust Muffler Tip 3.0i E53 | eBay.


BMW X5 DUAL EXHAUST TIPS STAINLESS CHROME 3.0L E53 | eBay

yes i've seen the "tips"

but the diesel exhausts come out under the bumper so these won't work unless you add more pipe

I was looking for clamp on so no fuss

o yea . im sorry i didnt even notice it was a diesel .. i also found this.. it works for a diesel but its a little pricey


Eisenmann Rear Muffler Exhaust Dual Flat Oval Tip BMW E53 X5 3.0d 99-04

I see what you mean.
I have done quite a few X5-3.0D exhaust now and I can tell you that there is no space there to bring a pipe from you outlet to come out over and out of the hole on the bumper!
Only way ,I could do it was to modify the outlet pipe,by cutting it and blocking on the back of the silencer and then open another outlet on the front of the silencer where the tailpipe can then be welded and fully working.
http://img806.imageshack.us/img806/5...eandafter1.jpg
http://img864.imageshack.us/img864/9892/p1010496.jpg
http://img822.imageshack.us/img822/3259/p1010497l.jpg
http://img267.imageshack.us/img267/6121/p1010423l.jpg
http://img546.imageshack.us/img546/6650/photo114f.jpg

The easiest with less work is to add a pipe to the existing outlet pipes and fit tail pipes of your choice,a bit like this....(not my liking at all :confused:)
http://img855.imageshack.us/img855/9...stupidtips.jpg

oh my god

that 2nd pic is crap that looks like it was done in a bodgit and scarper garage

The first one is the right idea alot of work to acheive it

I was looking for 2 round or oval pipes each side could you do that??

I'm going to Alton towers in may i'll drop the car off LOL

regards

What 2nd pic is cra*??????The first pictures .with the exception of the last one ,are work in progress and before any welding!Also is extremely difficult to drill through the silencers as they are very hard stainless steel and we always break a few Cobalt drill bits when drilling.All pipes used were stainless steel and all professionally tig welded with stainless wire.