Xoutpost.com

Xoutpost.com (https://xoutpost.com/forums.php)
-   X5 (E70) Forum (https://xoutpost.com/bmw-sav-forums/x5-e70-forum/)
-   -   2011 E70 N55 misfire after changing spark plugs (https://xoutpost.com/bmw-sav-forums/x5-e70-forum/99579-2011-e70-n55-misfire-after-changing-spark-plugs.html)

davidwnv 01-19-2015 09:08 PM

2011 E70 N55 misfire after changing spark plugs
 
This is my first post, so I apologize in advance if I mess it up.

Spent the better part of a week chasing this problem down, did a lot of web searching and never really found a solid answer, so thought I would post my experience and hope it can save someone some time if they run into the same issue. Here's my tale of woe:

Bought this 2011 X5 used with just under 50k miles on it a year ago October. Car has been flawless. Changed oil and filter about 10 days ago, at 70k miles. While recording the event in the service log, noticed recommendation for spark plug change at 60k miles. Ordered and received 6 Denso FXE22HR-11 Iridium plugs, because I couldn't get the Bosch OEM's or the recommended NGK's in a timely manner. Searched the web for correct gap, the best I could come up with was 0.040" (1 mm). Measured the new plugs, and they were all right on, so installed them. Drove it to town, ran fine until I started back up a long hill to the house. When I put my foot in it, it bucked like a rodeo bronc. No codes, no mil light, just bucked like crazy. Let it sit overnight, started up next morning, and it immediately idled rough and threw the MIL on. Read the codes, and it was misfire on cylinder 3. Swapped the coils between 1 and 3 (because they're easy to get to), cleared codes and started again. Misfire on cylinder 1. Bought a new coil, installed, cleared codes and test drove. MIL light on and misfires on 5 of the 6 cylinders. At this point, I know it's not coil problem so started thinking what else it could be. Checked the gap on the old plugs, determined most were in the 0.030" to 0.032" range, with 70k miles of wear on them. Finally found some info on the web indicating turbo engines generally require smaller plug gap at high boost. Removed all the new plugs, gapped VERY CAREFULLY AND PRECISELY to 0.025" and reinstalled. Test drove and VOILA! Car runs like new.

Long story short:

The N55 engine apparently likes a smaller plug gap than indicated by all the specs I could find on the web. 0.025" worked for me.

If anyone knows what the gap on the OEM Bosch plugs is, please post. If this hadn't worked, my next step was going to be to buy a set of the Bosch plugs.

Hope this helps someone out there.

Dave

Carson City, Nevada

ard 01-20-2015 12:20 AM

As youve seen, turbo cars can be very picky about their plugs. Personally I would ONLY go with OEM plugs- not "fits' but rather 'same vendor same plug' as OE.

Amazon Prime FTW. ;)

Kudos for DIYing.

davidwnv 01-20-2015 12:45 AM

Thanks, Ard...

As a rule, I agree with you. The OEM plugs on amazon prime were out of stock when I needed them, and I didn't want to pay $20/plug. After I already had the Denso's, I found the Bosch on autohausAZ (Select Your Model) for less than the Denso's!

Had the Denso's not worked, I was prepared to pull the trigger on a set of OEM plugs. I'll update this thread after I get some miles on these, or if I have any more trouble with them. Took a run to Reno this evening for dinner, and pushed it pretty hard, with nary a stumble, so I have my hopes up.

Thanks again for your reply!

Dave

BTW, I can do a complete in and out, including R&R all the appendages (panels, filters, tubes, etc.) in little over an hour. Practice makes perfect!


All times are GMT -4. The time now is 03:22 PM.

vBulletin, Copyright 2024, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved.