Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > Other BMWs
Fluid Motor Union
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 10-26-2022, 09:00 AM
Member
 
Join Date: Jan 2021
Location: Canada
Posts: 23
GuoyuII is on a distinguished road
Use BMW Rheingold ISTA to Do Programming and Coding

BMW ISTA BMW Software Preparations
* BMW Rheingold
* How To Install BMW Rheingold ISTA BMW Software
* Preparing vehicle programming and finishing off
* The basic requirement for efficient programming is that the vehicle is correctly prepared


How to Use BMW Rheingold ISTA to Do Programming and Coding Preparations
* Park vehicle on flat and even ground
* Wherever possible, protect vehicle from direct sunlight
* Turn off engine
* Shift manual transmission to Neutral or automatic transmission to Park
* Activate electromechanical parking brake or apply parking brake
* Make sure that the temperature of the transmission fluid is between -40 ??C (-40 ??F) and 85 ??C (185 ??F)
* Switch off all electric loads, lights and turn signal lamps
* Switch off wiper/washer system. The wipers may be actuated during programming and initialization. Make sure that the wipers can move freely
* Make a note of all stored radio and TV frequencies as well as the navigation destinations
* Connect up a BMW Group-approved battery charger in the engine compartment
The battery charger connected during programming must be run in “external power supply mode with battery connected”. Please refer to the operating instructions for the battery charger
* Do not connect or disconnect the battery charger during programming. Low system voltage may cause programming to cancel. Make sure that the vehicle system voltage does not drop below 13.0 volts while programming is in progress
* Set up connection between workshop network, vehicle interface and vehicle
* Check cable routing. Cables routed through open windows could be damaged when the windows are started automatically. Do not route cables through open windows
* Switch on ignition (terminal 15)
* On vehicles with Comfort Access, the identification transmitter must be inserted in the ignition lock. The coding procedure may be terminated if the identification transmitter is not inserted in the ignition lock.
* If the vehicle model does not have an ignition lock, the identification transmitter must be located in the vehicle interior.
* On vehicles with automatic terminal 15 shutdown (as from 03/2007) the signal from the door contact switches off terminal 15 by opening and closing the driver’s door. Terminal 15 is permanently switched on by pressing the START-STOP button. Make sure that the driver’s door contact is not operated during the programming procedure.
* Perform a vehicle test with the ISTA workshop system to make sure that all installed control modules respond and any fault memory entries are read out
* Before programming, rectify any faults that may be present and delete any fault codes stored
* Determine CBS data, note down and end ISTA BMW Software
* Preparations: Remove inserted data media (DVD) and disconnect connected data (iPod?, etc.). Data media in a drive or still connected could cause programming to abort
* Before starting vehicle programming, make sure the boot lid is closed (to prevent the luggage compartment lighting from overheating)
__________________
Knowing what I want to do, in the dead of night, ask myself my future plans, and move in that direction to realize it.(www.cnautotool.com)
Reply With Quote

Sponsored Links

  #2  
Old 01-18-2023, 01:12 AM
Member
 
Join Date: Jan 2021
Location: Canada
Posts: 23
GuoyuII is on a distinguished road
Hello, Dear friends ,good new,the bmw icom software have updated to 2022.12

V2022.12 Newest Vsrsion Software ISTA-D ISTA 4.37.43 ISTA-P 3.71.0.200 with Engineer Programming

Software Version : V2022.12
ISTA – D: 4.37.43 with SDP Programming Database 4.37.43
ISTA – P: 3.71.0.200 with Engineer Programming,supports the programming of BMW motorcycles and electric vehicles can program F/G/I/K chassis for car (through the ICOM, not other cable )
Vin: V2022.09.20
BMW ETK: 2019.12
BMW KSD: 2019.12 Multilanguage
BMW FSC Navigation Code Generator
BMWAiCoder for BMW Coding
Win10 64 bit operating system

BMW ICOM V2022.12, With free Software:
1. Get engineer version, INPA 5.06,winkfp 5.2.3,NCS 3.5.1, e-sys 3.31,data V71.0
2. get Chinese software DR.GINI B022
3. get count code navigation tool software FSC operator code
4. get one-clik hidden brush tool BMWAi V4.6
5. Add DIS Software for Old cars, DISV57 and DISV44,diagnosis and programming for BMW virtual machines
6. Support Vehicles: For BMW Cars,For BMW Motorcycle,For Rolls-Royce, For Mini Cooper

Notice : The software installed English language in default.
__________________
Knowing what I want to do, in the dead of night, ask myself my future plans, and move in that direction to realize it.(www.cnautotool.com)
Reply With Quote
Reply

Bookmarks

Tags
bmw ista bmw software

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 02:02 PM.
vBulletin, Copyright 2024, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.