Proud new x5 owner! 2001 - 4.4i

[CHE53]

Just thought I'd introduce myself, I've been researching the X5's for quite a while. Found a model I liked, then waited for a low mileage/reasonably priced one to pop up.

Low and behold, day before yesterday I found the one locally! Carfax'd it, inspected it, Drove it, loved it, bought it.

2001 Silver, 19" wheels, blk interior, 4.4 Sport pkg & Navigation. Only 65k miles!

I'm not new to the BMW realm (also have a swapped ti), however I am new to the BMW V8/Auto Trans..

Right off the bat, I have two questions which I couldn't find any definitive information on through searching.

-The swap from mkIII to mkIV navigation, is just a matter of buying the DVD unit, and following procedure outlined on bimmernav to "Plug and Play" the unit? End of story? Seems too easy..

-Flushing the Auto-Trans fluid.. I know that BMW cars historically have weak auto transmissions.. at 65k is it too late for me to worry about? (My mom's 06 x5 3.0 is at ~50k.. perhaps a good time to flush hers too?)

Thanks guys! I look forward to countless hours of reading through these forums, haha.

[IMG][/IMG]





The School parking posse




Here is the other toy too, in case anyone was curious

[tmv]

Congrats and

Do NOT flush the tranny. Do a drain and re-fill twice with filter changed, 1k miles apart. Find out what tranny you have and use correct ATF.

[CHE53]

Originally Posted by tmv

Congrats and

Do NOT flush the tranny. Do a drain and re-fill twice with filter changed, 1k miles apart. Find out what tranny you have and use correct ATF.

Ah I see, that seems smart. I'll figure out what that entails then. And thanks for the welcome!

congrats on the find!!!

MK3 ---> MK4... remove MK3... connect MK4... done... update MK4 software to the latest with perspective view if not updated already...

tranny... do as TMV said... it is not just the mileage, it is also the age... i would not touch it...

Good to know definitively on that Nav then. Thank you for that. The MKIII setup just feels so archaic how it sits, and the MKIV are about what you pay for a decent TOMTOM anyways.

But yeah I think I'll follow what TMV said for the tranny then.

Thanks!

Completely disagree... No fluid is "lifetime" and no filter can un-clog it's self

At 100k miles I dropped the pan on my ZF 6HP26X, changed that filter and topped it back off with redline D4. Then about 1k miles later, drained and re-filled it a 2nd time and now my tranny is VERY happy!! And no... no one had ever done any kind of service on it prior to this.

I see.. I think I will go talk to the material science specialist on campus about this to see what his perspective is on the metal particles inside the lubrication fluid. This is the type of thing they dedicate their lives too.. So maybe he'll have some interesting input?

Good to hear this method worked for you even after 100k miles though! gotta love that! Nobody want to spend all that $$$ on a rebuild that may or may not last..

[Whitecat]

Hey Welcome and congrats !! Here is a link for your sat nav dvd update

2013 BMW Navigation DVD High Version Map Update East Disc Replaces 2012 BMW | eBay

[CHE53]

Originally Posted by Whitecat

Hey Welcome and congrats !! Here is a link for your sat nav dvd update

2013 BMW Navigation DVD High Version Map Update East Disc Replaces 2012 BMW | eBay

Hey look there, Thanks for that! A lot cheaper than I thought they were going to be..

Congrats and

But:

Thanks for the welcome! Haha, I know I know.. I'll upload some shortly! School has been insane this week.

Forget the metal particles. They are irrelevant. If they are large enough to be caught by the filter, they won't do any harm. If they are small enough to pass through, by definition they are below the critical size you need to worry about. Transmission fluids lose their additive package effectiveness more than anything else. Lubricity isn't the failure mode you need to worry about.

It isn't a material (fluid) science question. It is a system question. There is no debate that new fluid is "better" in an absolute sense. The two points of debate are (1) whether installing that high-detergent new fluid in an aged system that is contaminated from normal use will result in the detergents loosening and shifting the contaminants, thus causing a blockage in the valve body and subsequent failure, and (2) whether the fluid condition is the cause of transmission failures, early or otherwise, ie before the transmission would have had a non-fluid-related failure in any case. In the case of (2), the other approach is to put aside the money you would have spent on original Lifeguard fluid and save it for when a sensor or other item fails in the transmission. It may sound like it, but this approach isn't fatalistic. It is driven by the desire to reduce the total cost of ownership.

There isn't one correct answer.

Preventative maintenance is a good thing. But maintenance that isn't preventative is just sunk cost. After 12 years in that transmission, if it was shifting fine, I would leave it alone, as I don't think the mileage is as much of an issue as the time.

That is some very informative input. I hadn't realized that the detergents were even a factor in all of this. But that definitely does make sense.

I've done some more reading on the subject, and it appears that often times transmission fluid lubricity isn't incredibly affected by time (like you said), as it is heat. If the transmission was ever run at excessive temperature the ATF will degrade at an exponential rate, because it is outside of the specific ATF design parameters.

-With degraded ATF comes slipping/more overheating (IIRC)
-Also, a possible sign of overheat would be discoloration of the ATF (though other things may cause this too? May not be a dependable method..)

I definitely agree with you though.. There isn't one correct answer, with the exception of a known-overheated transmission, it seems like a roll of the dice either way. (being a used car and all)

[JCL]

Originally Posted by CHE53

I hadn't realized that the detergents were even a factor in all of this. But that definitely does make sense.

I've done some more reading on the subject, and it appears that often times transmission fluid lubricity isn't incredibly affected by time (like you said), as it is heat. If the transmission was ever run at excessive temperature the ATF will degrade at an exponential rate, because it is outside of the specific ATF design parameters.

-With degraded ATF comes slipping/more overheating (IIRC)
-Also, a possible sign of overheat would be discoloration of the ATF (though other things may cause this too? May not be a dependable method..)

I definitely agree with you though.. There isn't one correct answer, with the exception of a known-overheated transmission, it seems like a roll of the dice either way.

By design, transmission fluids are meant to last a long time, so they have a high level of detergents. The level of those detergents drops over time, naturally. People use phrases like "shock to the system" and "particles sticking" when what is really happening is that putting in those detergents cleans it out, moves all the (normal) deposits, and that is what causes the post-fluid-change problems, as there isn't anywhere for them to go, they end up blocking tiny passages and check valves in the valve body, and then you have a shifting problem. You can do several changes, and effectively flush this all out, but you are hoping that in the meantime, nothing affects the valve body.

The additives are also there to provide thermal stability. If the fluid is overheated (abuse, slipping clutches, etc) then it will break down, and the additives won't function as designed. Overheated fluid changes colour, and smells burnt. If the fluid isn't burnt, I would say the chances are the additives are still good. There are transmissions that have run hundreds of thousands of miles on the original fluid, so it isn't like the fluid has a sell-by date. It can last fine, as long as it isn't overheated.

There are also additives in there to modify the friction characteristics of the fluid, right at the point of clutch engagement. Those are what are different from fluid spec to fluid spec (Dexron, Mercon, ZF Lifeguard 5, Lifeguard 6, etc). All the fluids are essentially a 10w hydraulic oil, with different additives. The clutches in any particular transmission design expect a certain fluid frictional characteristic and are tuned to that spec. Using a different fluid is a common way to fail a transmission, if they slip too much (now you get overheating, see above). If they don't slip enough, you get grabbing, and things break. Equally bad. There is no way to test the fluid for those additives remaining, this isn't like a viscosity test. If the transmission is shifting well, that is a good indication of the fluid being in spec in this respect. If it isn't shifting well, then you can go ahead and replace the fluid and see if that helps. It may. It may not. Depends on the actual problem. But it is a cheap first attempt before pulling a transmission. Back to the fluid change philosophy, though: if it is shifting fine, then these characteristics of the fluid are likely fine.

Then there is the viscosity of the fluid. It doesn't much matter, IMO, not like engine oil. Dexron III went to Dexron VI, with a signficant change in viscosity, and was backwards compatible. The transmissions that use that fluid spec don't care much. But, older fluid tends to be thicker (due to worn clutch material, which is non-metallic, but a thickening agent in practice). Putting in new (thinner) fluid, although returning to the right viscosity spec, means that things that didn't leak pressure (internal seals, not gaskets to the outside) may not hold. That can be another failure mode with a fluid change. No guarantee that it will happen, but it has happened before.

Finally, there is lubrication. This is the reason that many claim they want to change their fluid, to make sure everything is well lubricated. That sounds good in theory, but the first thing to remember is that oil (of which transmission fluid is a type) never loses its slipperyness. It gets contaminated, but it never stops being slippery. Even when it breaks down due to heat. The thing to remember is that transmission fluid has several functions. It is a cooling medium, it carries heat to the heat exchanger (and the other way, during warm up). It is a hydraulic fluid that can not be compressible, ie it has to transmit pressure from actuators, turbine blades in the torque converter, etc. And finally, it is a lubricant. Of all of those purposes, the lubricating is actually the least important. Transmissions fail due to heat. They function due to hydraulic actuators and pressures. But as to lubrication, that is the lowest demand put on a transmission fluid. That is why viscosity doesn't matter much. It is why a straight 10w oil works fine. It just doesn't see the same bearing loads, shear, etc, that engine bearings see. Yet lubrication properties are the thing fluid manufacturers talk about. They use the word synthetic as if it matters at all. It just doesn't. Stability over time does. Additives do. Resistance to oxidation does. But how slippery it is is way down the list. That is why a transmission can run 200,000 miles on the same fluid, and why comparisons to engine oil ("no oil is lifetime") are not as relevant when discussing transmission fluid.

Probably more than you wanted to know about transmission fluid. Again, there is no one answer as to whether to change it or not. If changed regularly, ie every 30,000 miles or so, there is low risk of a fluid change causing a problem. If changed at higher mileage, or after many years (regardless of mileage) then there is more risk of a fluid change causing a problem. And in all of those examples, at whatever mileage, you have to decide whether the benefit of new fluid is high enough to warrant the cost of a change, or if you do it right, multiple changes. Analogies to coolant, brake fluid, engine oil, etc, all of which benefit from regular changes, are not as relevant here.

If you do change it, only use an OE BMW filter (or a ZF part number), never a generic one. And only use ZF fluid in your case, or a fluid that is certified to meet the ZF standard, not one that says it is "suitable for applications that call for ..." and definitely not a univeral fluid that claims to be good for all transmissions, things like D4. They may work fine. But the odds are lower. And with transmission fluid changes, it is all about playing the odds.

[JCL]

Originally Posted by CHE53

I see.. I think I will go talk to the material science specialist on campus about this to see what his perspective is on the metal particles inside the lubrication fluid. This is the type of thing they dedicate their lives too.. So maybe he'll have some interesting input?

Forget the metal particles. They are irrelevant. If they are large enough to be caught by the filter, they won't do any harm. If they are small enough to pass through, by definition they are below the critical size you need to worry about. Transmission fluids lose their additive package effectiveness more than anything else. Lubricity isn't the failure mode you need to worry about.

It isn't a material (fluid) science question. It is a system question. There is no debate that new fluid is "better" in an absolute sense. The two points of debate are (1) whether installing that high-detergent new fluid in an aged system that is contaminated from normal use will result in the detergents loosening and shifting the contaminants, thus causing a blockage in the valve body and subsequent failure, and (2) whether the fluid condition is the cause of transmission failures, early or otherwise, ie before the transmission would have had a non-fluid-related failure in any case. In the case of (2), the other approach is to put aside the money you would have spent on original Lifeguard fluid and save it for when a sensor or other item fails in the transmission. It may sound like it, but this approach isn't fatalistic. It is driven by the desire to reduce the total cost of ownership.

There isn't one correct answer.

Preventative maintenance is a good thing. But maintenance that isn't preventative is just sunk cost. After 12 years in that transmission, if it was shifting fine, I would leave it alone, as I don't think the mileage is as much of an issue as the time.

[TerminatorX5]

congrats on the find!!!

MK3 ---> MK4... remove MK3... connect MK4... done... update MK4 software to the latest with perspective view if not updated already...

tranny... do as TMV said... it is not just the mileage, it is also the age... i would not touch it...

[BigBlack48is]

Originally Posted by TerminatorX5

congrats on the find!!!

MK3 ---> MK4... remove MK3... connect MK4... done... update MK4 software to the latest with perspective view if not updated already...

tranny... do as TMV said... it is not just the mileage, it is also the age... i would not touch it...

Completely disagree... No fluid is "lifetime" and no filter can un-clog it's self

At 100k miles I dropped the pan on my ZF 6HP26X, changed that filter and topped it back off with redline D4. Then about 1k miles later, drained and re-filled it a 2nd time and now my tranny is VERY happy!! And no... no one had ever done any kind of service on it prior to this.

[TerminatorX5]

Originally Posted by BigBlack48is

Completely disagree... No fluid is "lifetime" and no filter can un-clog it's self

At 100k miles I dropped the pan on my ZF 6HP26X, changed that filter and topped it back off with redline D4. Then about 1k miles later, drained and re-filled it a 2nd time and now my tranny is VERY happy!! And no... no one had ever done any kind of service on it prior to this.

i never said it was lifetime - it is not... nothing is lifetime... well... maybe the pyramids...

the problems with those gears is that as they wear off and contaminate the fluid, the material builds up inside and becomes part of the fluid - if it has not been changed early in the cycle, those chunks of the metal shavings inside actually "help" prolong the agony of the system... however, once you remove them and fill the void with the fresh fluid, the worn gears do not have the gunk to stick to and they start to slip...

i am tryinig to say, that if the tranny was not serviced before 40K, then just let it be... if it was serviced at that time, then do the regular changes at regular intervals..

it is like dental clean up - the moment after the clean up, the teeth are very sensitive as they protective layer of "gunk" is removed... I am not saying that you should stop doing the semi-annual dental clean-ups!!! just a reference to the tranny!!!