Best Coil Suspension Conversion Kit?

[TiAgX5]

I wonder how many coilover owners actually set them up correctly.......

Adjusting The COMPRESSION (Bump) Damping Control (Very Important to do this FIRST!)
Bump damping controls the unsprung weight of the vehicle (wheels, axles, etc.). It controls the upward movement of the suspension as when hitting a bump in the track. It should not be used to control the downward movement of the vehicle when it encounters dips. Also, it should not be used to control roll or bottoming.

Depending on the vehicle, the ideal bump setting can occur at any point within the adjustment range. This setting will be reached when "side-hop" or "walking" in a bumpy turn is minimal and the ride is not uncomfortably harsh. At any point other than this ideal setting, the "side-hopping" condition will be more pronounced and the ride may be too harsh.

STEP 1: Set all four dampers on minimum bump and minimum rebound settings.

STEP 2: Drive a moderately bumpy road briskly to get the feel of the car. Note: When driving the car during the bump adjustment phase, disregard body lean or roll and concentrate solely on how the car feels over bumps. Also, try to notice if the car "walks" or "side-hops" on a rough turn.

STEP 3: Increase bump adjustment clockwise 3 clicks on all four dampers. Drive the car bumpy road again. Repeat Step 3 until a point is reached where the car starts to feel hard over bumpy surfaces.

STEP 4: Back off the bump adjustment two clicks. The bump control is now set. Note: The back off point will probably be reached sooner on one end of the vehicle than the other. If this occurs, keep increasing the bump on the soft end until it, too, feels hard. Then back it off 2 clicks. The bump control is now set.

Adjusting the REBOUND Damping Control
Once you have found what you feel to be the best bump setting on all four wheels, you are now ready to proceed with adjusting the rebound. The rebound damping controls the transitional roll (lean) as when entering a turn. It does *not* limit the total amount of roll; it *does* limit how *fast* this total roll angle is achieved. How much the vehicle actually leans is determined by other things such as spring rate, sway bars, roll center, ride heights, etc.

It should be noted that too much rebound on either end of the vehicle will cause an initial loss of lateral acceleration (cornering grip) a that end which will cause the vehicle to oversteer or understeer excessively when entering a turn. Too much rebound control in relation to spring rate will cause a condition known as "jacking down." This is a condition where, after hitting a bump and compressing the spring, the damper does not allow the spring to return to a neutral position before the next bump is encountered.

This repeats with each subsequent bump until the car is actually lowered onto the bump stops. Contact with the bump stops causes a drastic increase in roll stiffness. If this condition occurs on the front, the car will understeer; if it occurs on the rear, the car will oversteer.

STEP 1: With rebound set on full soft and the bump control set from your earlier testing, drive the bumpy road, paying particular attention to how the car rolls when entering a turn.

STEP 2: Increase rebound damping three sweeps (or 3/4 turn) on all four dampers and drive the road again. Repeat Step 2 until the car enters the turns smoothly (no drastic attitude changes) and without leaning excessively. An increase in the rebound stiffness beyond this point is unnecessary and may result in a loss of cornering power. Note: As with the bump settings, this point will probably be reached at one end of the car before the other.
However, individual drivers may find it desirable to have a car that assumes an oversteering or understeering attitude when entering a turn. This can be easily "dialed-in" using slightly excessive rebound settings at either end.

When I read posts that state "my car corners much flatter with my new coilovers", my thought is spring rates are too high or low rate damping is set WAY to stiff for street use, the vehicle is a wreck waiting to happen.

Stiffer sways reduce roll, and on roads with less then perfectly smooth paved curves, reduced unsprung weight helps increase control (this is where 315s on 20 or larger actually work AGAINST ideal control/handling.)


Some will argue this does not need to be done on a street vehicle, but undesireable handling is not something you want to experience during an emergency situation on public roads. Lives could be lost.