Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > X5 (E70) Forum
Fluid Motor Union
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 02-03-2010, 09:35 PM
Member
 
Join Date: Dec 2009
Location: Atlanta, GA
Posts: 268
Xtony is on a distinguished road
DIY Front Brake Pad Replacement '08 4.8L

Just got rid of the dusty stock front pads and installed Carbotech Bobcats which had to be custom made for the 4.8 front brakes. Here are a few pictures of the procedure. If you've done brake pads on BMWs before, there's really nothing new other than the anti-rattle clip now includes a dust shield, the brake pad sensor wire is much sturdier, and the brake fluid reservoir is hidden under a plastic grill. Oh, I also noticed my sport package wheels are made in Mexico!

Please don't attempt this unless you know what you're up against. Working on brakes can have dangerous consequences. I am comfortable doing this type of work since I run my e46 M3 on the track, and in fact never trust anyone with my brake work.

First of all make sure your e-brake is set. Slightly loosen the lug bolts before lifting the tire fully off of the ground. Lift the front of the truck by using the lift pad located in the plastic under engine cover.

Set the truck down onto jackstands using the side jack pads.

Remove wheels. Mine were already difficult to remove due to rusting although my X5 has never seen road salt. Banging the tire from behind with a loose lugbolt to keep the wheel from hitting the ground worked for me. Remove the anti-rattle clip/dust shield by prying it off with a screwdriver.

Now remove the plastic caps that covers the caliper carrier bolts/pins. They are located on the inside of the caliper at the top and bottom. turning the wheel so you can see behind the caliper helps. The caps just pry off with a thin blade screwdriver.

Now using a 7mm hex socket and long breaker bar remove the two caliper carrier bolts. They shouldn't be very tight. The bolts are inside of a rubber sleeve and you will have to grab them and pull them out once they have been totally loosened.


Once the two bolts are out wiggle the caliper as you pull to the rear of the car to remove the caliper. Once the caliper is removed secure it with a bungee cord or metal hanger to keep the caliper from damaging the attached brake fluid hose. Remove the old pads. The inboard pad will be stuck inside the caliper cylinder by three prongs on the backing plate of the inboard brake pad.

Unless the brake pads you have removed are fairly new, you will now have to compress the caliper piston to make room for your new pads. I use the old inboard pad with a C-clamp to compress the piston. Before doing this you will need to uncap the brake fluid reservoir. The reservoir is located under a plastic grill near the firewall on the driver's side of the engine compartment. The grill is easily removed after loosening four plastic quick release bolts.


Once the piston has been compressed clean everything up and install the new pads. One has the clips that go in the caliper piston and the other just slides into the front of the caliper carrier. You probably want to pretreat the backing plates and the arms of the new pads with CRC anti-squeal goop.

Slide the caliper back into place. Reinstall the caliper carrier bolts. Sometimes you will need to jiggle and press the caliper in order to get the bolts started in their hole. Make sure you're not stripping the bolts. Torque them to 22-24 ft-lb. Replace the anti-rattle clip by sliding it front to back until the prongs drop into place. It can be a pain to get it in.

On to the driver's side. Everything is the same except that there will be a brake pad sensor pressed into the inboard pad.

Remove the sensor by grabbing it with needle nose pliers close to where it enters the pad. Make sure you don't lose the metal spring device that holds the sensor inside the pad. Sometimes it will stay in the slot of the old pad.

Here's a picture of the sensor with the metal spring clip in place.

Make sure you install it after you finish replacing the driver's side pads. You might want to practice sliding it into the pad before you install it, just so you know what you're doing since it's hard to see once the caliper is reattached.

Before you reinstall your wheels, apply a thin layer of anti-seize compound to the mating surfaces of the wheel and rotor/hub to keep them from rusting together. Enjoy your dust free wheels!

Last edited by Xtony; 02-03-2010 at 09:41 PM.
Reply With Quote

Sponsored Links

  #2  
Old 02-03-2010, 10:35 PM
shashankmittal's Avatar
Member
 
Join Date: May 2009
Location: Boston MA
Posts: 264
shashankmittal is on a distinguished road
Awesome! thanks for the instructions. I am sure lot of people would benefit from this. I am myself very interested in getting bobcat pads. Do let us know about their performance and dust, once you have tested them thoroughly.
Reply With Quote
  #3  
Old 02-03-2010, 10:47 PM
Member
 
Join Date: Oct 2007
Location: USA
Posts: 1,984
Penguin is on a distinguished road
Excellent DIY with really good photos!

The only thing I might add is that if the brakes haven't been bled for a while, one might want to bleed them while you're in there and working on things.
Reply With Quote
  #4  
Old 02-05-2010, 08:30 AM
Member
 
Join Date: Dec 2009
Location: Atlanta, GA
Posts: 268
Xtony is on a distinguished road
I'll report back on how the pads perform once I've put a few hundred miles on them. Just bedded them last night. So far, so good!
Reply With Quote
  #5  
Old 02-05-2010, 11:49 AM
wallyx5's Avatar
Member
 
Join Date: Oct 2007
Location: Central Coast, CA
Posts: 931
wallyx5 is on a distinguished road
Nice write up.
__________________
_________________________________________________
2010 X5M /// R63 AMG...Wifey's 540HP Family Hualer

2001 X5 3.0i Sport 335,448 miles & counting...

SMG M3 Steering wheel
E46 Stainless Racing Headers
4.6is Exhaust
Turner Pulleys
Afe Intake
Brembo drilled rotors
PowerFlex Bushings

Hualingan
30mm H&R Spacers rear
20mm H&R Spacers front

Bavarian Autosport High-Performance Coils
Active Autowerke's Performance Software
Reply With Quote
  #6  
Old 09-08-2010, 09:03 AM
Member
 
Join Date: Jul 2008
Location: usa
Posts: 91
alefcole is on a distinguished road
How about the rear pads?. Is this procedure the same?
Reply With Quote
  #7  
Old 09-08-2010, 03:14 PM
Member
 
Join Date: Dec 2009
Location: Atlanta, GA
Posts: 268
Xtony is on a distinguished road
Haven't done the rears yet, but I just ordered some Akebono Euros for the rear since now the rears get so much dirtier than the fronts. Can't imagine the rears being much different.

BTW, so far the Carbotechs have been great. Good initial bite, low dust, and NO squealing.
__________________
Reply With Quote
  #8  
Old 05-17-2011, 11:16 AM
Member
 
Join Date: Sep 2010
Location: canada
Posts: 1
swsherif is on a distinguished road
where to buy the pads , the dealer charge almost 650$ for front and rear
Reply With Quote
  #9  
Old 05-17-2011, 11:33 PM
Member
 
Join Date: Jan 2009
Location: Chicago
Posts: 5
Neilm3 is on a distinguished road
I've changed brakes on my m3 and 528 and the procedure looks to be the same as the x5.

xTony: Thanks for posting, great write up and pictures.
Reply With Quote
  #10  
Old 05-22-2011, 03:37 AM
Member
 
Join Date: Oct 2009
Location: Belfast
Posts: 11
Minny is on a distinguished road
Thank you for the write up and pictures. How did you reset the pad distance remaining countdown on the iDrive?
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 02:30 AM.
vBulletin, Copyright 2024, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.