|
Xoutpost server transfer and maintenance is occurring.... |
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Problems on upgrading OS MKI to V26
When trying to upgrade to V26 (1-1/80) the system says that the OS CD is correct ant starts the upgrade. When the upgrade is about halfway the CD ejects automatically and the system says that it's finished completly and tells me to remove the CD and press OK. After doing this I found out the OS was not upgraded and is still 1-1/72. I used a good quality CD-R and burnt it at the lowest speed possible (4x) using alcohol 120%. I also burnt V24 (nero image) wich automatically burnt at maximum, same story here, it was however recognised as a valid OS CD by the system. So I assume burn speed is not so much the issue here. What am I doing wrong? Thanks in advance, Arjen van Leeuwen The Netherlands |
Sponsored Links | |
|
#2
|
||||
|
||||
Quote:
JV
__________________
JV What gets us into trouble is not what we don't know...it's what we know for sure that just ain't so |
#3
|
|||
|
|||
Thanks for the reply, but BMW SI bulletin says differently (see the actual text below) The thing is that after upgrading the system says that I upgraded to version 8.0, after rebooting it appears that nothing has changed en in the setting menu it still stated 1-1/72.
According to the information on this site, version 1-1/80 should be present from version V17 onwards, this means that it's on every following version CD until a new version is available. When I want to upgrade to version 1-1/80 wich CD do I have to burn, 17 or any CD after that?? Thanks, Arjen SI B 84 01 02 Phone, Navigation Systems September 2005 Technical Service This Service Information Bulletin supersedes S.I. B84 01 02 dated March 2005. designates changes to this revision SUBJECT Navigation System Operating Software MODEL E38 (7 Series) E39 (5 Series) E46 (3 Series) E53 (X5) E83 (X3) E85 (Z4) E65/E66 (7 Series) SITUATION With the introduction of navigation system operating software V26, there are currently 2 valid versions of navigation software. Navigation system operating software V17.1 is used on MK III systems without "Split Screen". 1. Navigation system operating software V26 is used on MK I, MK II, all other MK III navigation systems, DVD navigation systems on I-Bus vehicles, NAVI01, NAVI02 and NAVI03. 2. CORRECTION Navigation system operating software should be updated under the following circumstances: The Navigation computer has been replaced. CIP program prompts the navigation software to be updated. If instructed by a Service Information Bulletin or the Technical Hotline. NEW FEATURES INTRODUCED WITH SOFTWARE V26 The actual location is shown as an arrow in a circle. The destination is marked with a checkered flag. Map Positioning in "Travel Direction" can now be selected in scales up to 100 mls. Disable Point of Interest (POI) icons is now selectable on I-Bus DVD NAV systems in: General Destinations Travel Information The following functions are now selectable on E65/E66 with NAVI03 (from 03/2005): Hide Map Icons General Destinations and Travel Information Note: After loading NAV SW V26, the vehicle must be driven to ensure the proper function of the Navigation system and the correct displaying (Interstate Icons). CHECKING SOFTWARE VERSION MK I Systems The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as " 1-1/80". The numbers have the following meanings: first digit 1 - is a 1st generation navigation system (MK I); second digit 1 - is a 1st device variant (top navigation – MK Ic color screen); the last two digits 80 - are the software version of the graphic component (8.0). MK II Systems The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as " 2-1/81". The numbers have the following meanings: first digit 2 - is a 2nd generation navigation system (MK II); second digit 1 - is a 1st device variant (top navigation – MK IIc color screen); the last two digits 81 - are the software version of the graphic component (8.1). MK III Systems The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as " 3-1/63" or "3-2/63"(MK III with split screen). The numbers have the following meanings: first digit 3 - is a 3rd generation navigation system (MK III); second digit 1 - is a 1st device variant (top navigation – MK IIIc color screen), or 2 – is a 2nd device variant (radio navigation – MK IIIm monochrome display); the last two digits 63 - are the software version of the graphic component (6.3). DVD navigation system for I-Bus vehicles The software version is shown in the top right corner of the "setting" screen. The software/hardware version is displayed as "5 -1/60". The numbers have the following meanings: first digit 5 - is a 5th generation navigation system (DVD); second digit 1 - is a 1st device variant (top navigation – DVD color screen); the last two digits 60 - are the software version of the graphic component (6.0). E65/E66 Systems Enter the Service Mode of the Control Display Select "MOST Devices" Scroll down and select "Navigation" Scroll down a few pages until "Software Version" is displayed Software Version for CD navigation (NAVI01) should be 7.3.2 (I-level E065-05-03-810.2). Software Version for DVD navigation (NAVI02) should be 8.4.4 (I-level E065-05-03-800.2). Software Version for DVD navigation (NAVI03) should be 9.2.1A (I-level E065-05-09-500.2). Current Software Versions Software version Application 8.0 MK I - E39/E38 (up to 9/97) 8.1 MK II - E39/E38 (from 9/97), E46, X5 9.0 MK II - Radio Navigation – E52 (Z8) 5.1 MK III Radio Navigation – E52 (Z8) from 09/00 3.1* MK III w/o Split Screen -E46 from 06/00, E39/E38 from 09/00, E53 from 10/00 6.3 MK III with Split Screen 6.0 DVD Navigation 7.3.2 E65/E66 NAVI01 (CD-drive) 8.4.4 E65/E66 NAVI02 (DVD-drive) 9.1.16 E65/E66 NAVI03 (DVD-drive) *Included in Navigation software CD V17.1 LOADING SOFTWARE (ALL EXCEPT E65/E66) For MK I, MK II, MK III, and DVD NAV systems (except E65/E66) use the following software loading instructions: Turn ignition to position 1 (terminal R). 1. Do not cycle the key or perform diagnosis while installing the new software. Make sure that the power supply is stable, i.e. do not switch on any electrical loads. Activate "GPS-Navigation" and acknowledge the screen disclaimer by pushing the rotary knob. 2. Remove the map CD from the Navigation computer by pressing "eject" button. 3. Insert the Navigation Software CD (V17.1 P/N 01 59 9 789 299 index "x" for MK III without split screen, V24.1 P/N 01 59 0 141 891 index "r" for all other versions). 4. Mark I System (up to 9/97 production): 5. After a few seconds, the BMW roundel will appear on the board monitor and will be "filled in" clockwise to show the progress of loading (approx. 4-6 minutes). Mark II System (from 9/97 production), Mark III System (E46 from 06/00 and E38/E39/E52 from 09/00 production), DVD navigation system (E46, E39, E52 from 09/02 and E53, E85 from 10/02 production): After a few seconds, a menu of notes on loading procedure and "progress" bar appear on the board monitor. When the loading process has been completed, the message "Software has been successfully loaded" is displayed. Remove the operating software CD and confirm the end of the loading process by pressing the rotary push-button on the board monitor. "OK" appears in the display. 6. Drive the vehicle before delivering to the customer to ensure the correct function and displaying (Interstate Icons) of the Navigation system. 7. LOADING SOFTWARE (E65/E66 ONLY) When programming any E65/E66 using CIP 19.0 or higher, you will be prompted by the CIP "Update NAV control module:" screen that "BMW Navigation CD Version 26" must be loaded prior to programming the vehicle. Do not replace the Navigation Computer. Note: Connect an approved battery charger before loading software. Turn on ignition to Term R or Term 15. 1. Using the iDrive enter into the Navigation Menu. 2. Remove the map CD 3. Insert the Navigation Operating Software CD V26 (P/N 01 59 0 141 891 index "r") into the navigation computer and use CIP 19.0 or a more recent version for NAVI03 (DVD navigation). 4. Select "Yes" with iDrive Controller to install software. 5. The software will then load in two steps in approximately 10-15 minutes. 6. Do not touch the iDrive while the software is loading. 7. When the installation is finished the CD will be ejected. The message "Installation Successful, Remove Software loading CD and press OK" will appear. At this point select "OK" with iDrive Controller. 8. The Navigation system will then "reinitialize". 9. When prompted, insert map CD. 10. Refer to SI B09 05 01 (Coding, Individualization and Programming) for any necessary coding and programming. Note that CIP will automatically reprogram all programmable control units that do not have the latest software. 11. Drive the vehicle before delivering to the customer to approve the correct function and displaying (Interstate Icons) of the Navigation system. 12. NAVIGATION COMPUTER REPLACEMENT MK III When replacing a defective MK III computer, a configuration signal is required to allow the new computer to load the correct software for its respective application. This is generated by using DIS coding program "Coding ZCS C43.0" or higher and Navigation System operating software CD V 17.1 or V26. Connect DIS/GT1 tester to vehicle 1. From the DIS Coding/Programming select "1 ZCS Coding" 2. Select appropriate engineering series (E38, E39, etc.) 3. Select "4 conversion" 4. Select "3 IKE/Kombi" 5. Select "2 Language" 6. At prompt "Is the CD-ROM present?" – select "Yes", but do not insert Navigation CD into the Nav Computer yet! 7. First select the main language and then an additional language (the choices are: English, French, Italian, Spanish, German) 8. Select announcer's voice gender: male or female. 9. After activation of the automatic coding, the DIS tester tells you to follow the instructions on the monitor for Navigation CD installation. 10. Place the Navigation CD into the navigation computer CD drive. 11. Important: Do not switch ignition OFF during software loading procedure. Once loading has been completed, remove the CD and then confirm completion by pressing the rotary push-button on the monitor. 12. Turn ignition OFF for 10 seconds, then turn it ON and conduct a functional check. 13. After this step has been finished, encode the Navigation computer in the regular manner using the path "1 Recoding". 14. TROUBLESHOOTING HINTS The following problems may occur during the software loading procedure: The message "CD defective" appears on the display screen. The message "Fault during programming" appears on the display screen. The message "The system is restarting" appears on the display screen. The installation process has stopped and the display screen is blank and the power LED on the navigation computer is off. The CD will not eject. These complaints are usually the result of a faulty Navigation Operating software CD. For points 1-3 for error messages that appear on the display screen, check for the correct software version and try loading a new Navigation CD. For a CD that will not eject from the Navigation computer follow the procedure below: Remove the Navigation computer. 1. Unplug the voltage supply (blue connector). 2. Reconnect the voltage supply and immediately press the eject button repeatedly until the CD in the drive is ejected. 3. Insert a new Navigation CD and restart the installation process. 4. PARTS INFORMATION Part Number Description 01 59 9 789 299 Navigation Software CD V17.1 Index "x" 01 59 0 141 891 Navigation Software CD V26 Index "r" Copies of the CD V26 will be shipped to every BMW Center through the Automatic Tool Shipment Program. [ Copyright © 2005 BMW of North America, LLC ]
|
#4
|
|||
|
|||
I have the exact same problem with the MKI in my 98 E38. It says it is successfully upgraded to V8.0 but the screen then shows it's still at 1/72.
|
#5
|
|||
|
|||
It seems, that`s the last version of software to MK1, cause i got same problem 2.
__________________
E38 740i M60B40 Individual Bullet Version |
#6
|
|||
|
|||
There are 2 sets of nomenclature for the old MKI, SW and MMI. I have seen that the Nav has one set of software and the Video Module has another. The screen shows the one for the VM. The MKI nav can't work without the VM as they have a special small connection plug the none of the other later VMs have and also the MKII and later can work without a VM but MKI can't. The screen will never show higher than 1-1/72 even for SW of 8.0 They stopped upgrading MKIs at Ver 15. 15 and all above give you the same. I had a MKI from the factory in my car and then went to MKIII and MKIV.
|
Bookmarks |
Thread Tools | |
Display Modes | |
|
|
|