My E53 Audio Upgrade - Stage 1 - Subwoofer & Monoblock
 

Hi guys. I'm kind of new here so I thought I'd contribute a bit and do a build log for my 06 X5.

My mission with stage 1 of my audio upgrade was to add low end to the stock system.
My SAV has a stock 16:9 Screen, Navigation, bluetooth, steering wheels controls ect. it has the premium sound package with a DSP amp and 10 speakers so I figured a good way to start would be add a LOC interface/keeping my head unit and features and running a decent 12" sub and 1000-1500RMS of clean power.

I already had a line on the 13aV.2 though a friend and I have ran alot of their stuff I the past and liked it. And having heard them already on a Nine.1 I knew they could get pretty low and still sound pretty accurate as well.

The enclosure is custom.
Kerf Port/Recessed Mount/2.4 cubes/33hz

I grabbed the Nakamichi PA-1500 for a steal and after running their stuff in the past I'm thinking the sound quality and clean power will be there and match well with this single sub SQ orientated install.

I went with the Audio Control LC2i for the factory integration piece.
An audio engineer recommended something with bass restoration for my application with the stock DSP in the mix and the LC2i has their Accubass processing to prevent roll off at higher volumes on stock systems.

I plan on sourcing a DLS Component set, LC6i or LC8 and a mid amp for the stage 2 upgrade in the near future.

For wiring and fuse distribution I went with KNU. I Ran 0GA into the block with dual 4GA out for adding that mids amp for my stage 2 upgrade. 150A fuses on each circuit.

http://i171.photobucket.com/albums/u...ps073813f4.jpg

Elemental Designs 13A.v2 Dual 2ohm

http://i171.photobucket.com/albums/u...ps674754b8.jpg

This is one heavy woofer...And I love the surround I can't wait to see this thing flex!

http://i171.photobucket.com/albums/u...ps5132c429.jpg

http://i171.photobucket.com/albums/u...psb858c290.jpg

Nakamichi PA-1500 1200WRMS @ 1ohm

http://i171.photobucket.com/albums/u...ps38c6d7f4.jpg

Audio Control LC2i

http://i171.photobucket.com/albums/u...psbfe0af71.jpg

Knu KonFused Distro KNF-12 Single 0 or 4GA in to Dual 4 or 8GA out "Fused at 150A Per side"



http://i171.photobucket.com/albums/u...psf86775fe.jpg

Now for the install..

Obviously it helps to give a step by step guide for others that haven't been there before. :)

The bare canvas...

http://i171.photobucket.com/albums/u...ps1821a22f.jpg

Remove panel by changer/nav drive

http://i171.photobucket.com/albums/u...ps5fe2cc6b.jpg

Remove panel over stock sub/fuse Panel location this is the home for the LC2i so adjustments can be made easily.
I removed the stock subwoofer enclosure last week in anticipation of this install.
* It's just a couple of 10mm bolts on the floor pan and a Allen bolt behind the fuse block.

http://i171.photobucket.com/albums/u...psc31da26e.jpg

Now with those panels out of the way pull the floor panel up and expose the spare tire.
Remove the wing nut/retention plate and use the pull handle to lift the tire up out of the well it's a nice feature to save on broken backs. "Just don't forget to put the webbing and handle back under when returning the tire to the well.

http://i171.photobucket.com/albums/u...psbc7b79b9.jpg

After the tire is removed you will be left with the pod that houses the air pump for the self leveling rear air suspension. *Be careful not to stress or pinch any airlines coming out of this unit when working in this area. Remove the two 13MM bolts from the rear of the frame and two 13mm from the front of the bracket.

http://i171.photobucket.com/albums/u...ps9562d572.jpg

BEFORE CONTINUING DISCONNECT THE NEGATIVE BATTERY CABLE!

Now with the frame removed and set aside we can remove the cover for the radio module. It's secured by 3 Philips Head screws.

http://i171.photobucket.com/albums/u...ps940af60c.jpg

Once cover is removed we can pull some tape off the harness going into the radio module and connect into a 12V switched signal for our remote turn on wire for the amp.
"The wire we want is Purple with a white stripe"

http://i171.photobucket.com/albums/u...ps11d559c6.jpg

Next we solder, shrink wrap and zip tie the remote wire into the radio module harness

http://i171.photobucket.com/albums/u...ps2206ccbf.jpg

Now we can remove the cover on the floor by the former sub enclosure area.
It's secured by 2 10MM plastic nuts.


http://i171.photobucket.com/albums/u...psb0b845e9.jpg

With the plastic cover removed it's time to tap the harness from the stock subwoofers to get the signal for the LC2i.
We are after the twisted pair of Solid blue solid brown and solid yellow solid brown. The brown wires will be - and the yellow and blue wire are +


http://i171.photobucket.com/albums/u...ps6783cb9b.jpg

Time to add some length to get the signal wires back to the LC2i cubby.

http://i171.photobucket.com/albums/u...ps484eb3a4.jpg

The Ground is next. I've added a Ground wire for the LC2i as well.

http://i171.photobucket.com/albums/u...psfeff74ed.jpg

It will be connected to a factory frame ground point. No paint, bare metal. One 10MM nut secures it.

http://i171.photobucket.com/albums/u...psc61d29ec.jpg

Now for the Power and fuse distribution. OGA into the KNu block with 4GA out to the Nakamichi and a small 12V lead for the LC2i. The holder is zip tied to the frame rail hole noted in pic and small 12V routed to LC2i cubby.

http://i171.photobucket.com/albums/u...psc1dddd22.jpg

With 12V, Speaker Level inputs and ground supplied to the LC2i that can call be connected and put aside.

http://i171.photobucket.com/albums/u...ps68b6f7e2.jpg

And on to the amp.... I wanted it to be clean with accessibility to adjust and keep cool. So I decided to place it in front of my enclosure mounted to the floor with all the wiring hidden coming up from under.

So I did some measurements checked the underside for clearance and screwed it down into the floor cover. Now it time to drill out some wire routing paths.

http://i171.photobucket.com/albums/u...psbefb6eb2.jpg

Drilled out and wiring routed.

http://i171.photobucket.com/albums/u...ps0d26bb2e.jpg

Now for some speaker wire connections for the box. My SMS Box has brass bolts so I'm using these guys from the knu kit for now. I'll prob switch to a ring in the future.

http://i171.photobucket.com/albums/u...ps4a6a0f93.jpg

And the final result after cleanup and enclosure placement.

I'm very happy with the results :D

http://i171.photobucket.com/albums/u...psd72d2c1d.jpg

Clean install and nice write up!

Did you leave the wires for the amp long enough to still be able to lift up the cargo floor in the event of a flat?

Very nice. I bet it pounds. Nice write up. I'd love to hear it in person someday.

Nice write-up.
For lifting up the spare tire, attach the handle (small arrow) to the hook (where the top lift gate lock onto) on the lower lift gate. When you lower the lift-gate, the spare will be pulled up, then you slide it out. It wasn't design for pulling it by hand (eventhough you can use it that way) you are missing a plastic stick next to the tow hook, that keep the lower gate open so you can slide the spare out with both hand. It should be in the manual:D
http://i171.photobucket.com/albums/u...psbc7b79b9.jpg

A very nice and professional install there man!

Out of interest what do you set the Bass level on the head unit too?

Thanks man! I like to keep it clean and professional. I figure a clean, well engineered beauty like our E53 SAV's needed a decent install.
I left 6ft of extra wire under the floor for removal of the spare. This length worked perfect as the floor can be lifted out and rested against the tailgate for full access if necessary. The write up took a while but I figured if another forum member looking to add a sub and amp could benefit for a detailed guide it's worth my time and effort :thumbup:

Thanks You, And yes it does hit very looow. PM me anytime. I'm in the North Metro we can meet up. If you like the low end I'd be more than happy to help you install something in your E53.

Thanks TMV!
Good call on the proper use of the lifting strap. I will add that note to my DIY.
I was aware of it but didn't point out the proper use when I referenced the strap in the write up.
I think is a pretty slick design. The diagram is on the underside of the floor cover as well I believe.
My Plastic stick is laying in the spare tire well in this pic. it fell down when I was removing the SLS pod.

Thanks for your kind words. I actually have the bass level on my head unit just a notch or two above center "or Flat"

I have a remote level control for the amp to install and several adjustments on my LOC and AMP to dial in the amount of bass I'd like. So my application is not really the norm.

Here is a link to what someone found to be good settings for stock DSP on our vehicles. Hopefully this helps you.

http://www.xoutpost.com/articles/x5/...gs-bmw-x5.html

That's great Thanks a lot.

I plan on eventually fitting an after-market mono block amp and sub to my DSP system so your write up is perfect.

For the time being I'll try adjusting my DSP settings to the link you recommended.

front stage
 

I'm in the process of doing my second E53 and I've got to say that's some nice clean work....As far as your front stage I'd avoid the dls because they are tough to deal with in the u.s. I would instead opt for this setup which is very reasonably priced and will pretty much bolt right up with minimal mods....The Madisound Speaker StoreI I would also check out this guy's E39 build thread. This guy is an absolute guru on this setup and it works......I'm actually trying to upgrade to the alpine 701 processor and have full control from the head including bluetooth and navi...Wish me luck... I'll be starting the build in about two weeks and I'll try to post some pics.
Here's a list of my gear.
Processing/oem integration
Intravee ibus-ainet converter
Alpine pxa-h701
Alpine Kca-420i
Audio Control LC2i
Amps
2 each Jl Audio 600/4 HD
Jl Audio 750/1 Hd
Speakers
Front stage Hertz Mille Ml2800, Ml700, Ml1600 (full active setup)
Rear fill Audison Voce Midbass with Morel MdM 55 midrange Modified to fit factory housing (passive setup with mid to roll of at 7.5Khz)
Subwoofer Jl Audio 10w7ae in 1cu net sealed in modified factory location.
Power system
Optima Yellow Top (2nd battery next to spare tire in rear well)
Upgraded factory battery to East Penn Mfg Agm Intimidator)
Cadence high strand 0/1 gauge to jl dat blocks
homemade signal cables

Wow nice setup. The 13av.2 is a beast that was like the last good woofer elemental designs made. I have 2 11kv.2 installed. I didnt want to lose any trunk space so i just put them on both sides of the x in the back. That 13av is going pound hard. Only problem is ED is out of business unless they came back and i didnt know it -bad customer support- great products though.