Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > X5 (E53) Forum
Arnott
User Name
Password
Member List Premier Membership Search Today's Posts Mark Forums Read

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #61  
Old 01-26-2021, 02:46 PM
Member
 
Join Date: Mar 2008
Location: CYPRUS
Posts: 2,040
omodos is on a distinguished road
Quote:
Originally Posted by andrewwynn View Post
I realized something on the first two repair jobs I did for a broken door handle carrier: they broke exactly the same way and in large part due to a design flaw.

The flaw is this: the designers decided to incorporate feedback to the handle when locked (the handle resists lifting). The problem is that the little bar that blocks the handle gets slow in lubrication that gets gummy and slows the bar keeping the handle locked down when the door is unlocked.

UPDATE: when repairing a door actuator I realized that it will freeze and will not move, setting up another method to break your DHC. I will be making a thread describing the situation soon. The details are in another thread already but I'll make a clean new one.

(For about a week before I broke mine I noticed a second click about a second after unlocking the door I later learned was the blocking bar slowly moving into the unlocked position)

This is especially hazardous when this happens in frosty locations. When you live in a cold climate you are accustomed to the door seal freezing stuck where you need to tug extra hard to break the seal, the problem is the door latch is unlocked, the door seal is likely not frozen but the door handle is blocked.

When you tug on the handle thinking the door is stuck you put many times the normal force on the hinge of the door handle carrier. Enough times and fatigue failure will cause the pot metal to fail.

The good news is most often this break can be repaired with a zip tie! The better news is you can almost certainly shots L avoid the break in the first place of you cut the nub of the blocking bar when you put in a repaired or replaced door handle carrier.

I don't recommend OEM DHC. get a knock off that has good star review on Amazon etc and swap the Bowden cable from the OE part because the cables are kaarap from the China parts.

Here are the photos from my last DHC repair:


Here is the weakest link on the door handle carrier. Most will break right here











So here is the carrier I'm about to install. I've reenforced the weakest link with a nylon zip tie (don't have my stainless ones with me).

By placing the lock where I did it multiplies the strength it should hold if the pot metal breaks. I will try to do a test with the one I'm about to remove.

"I haz success"!

I was able to confirm that the double lock disconnects the lock mechanism so there is no need for the blocking bar that prevents lifting the handle when the door is locked.

I cut the little tab off that has been causing so much grief.


Red is the lock bar, blue is the tiny tab that actually blocks the handle when locked.


Blue is the tab and yellow is the part of the handle that is blocked


Blue arrow pointing to the empty space where the tab used to be.

So now it's as it should have been from the beginning and how BMW decided to change them to on the current cars.

The handle pulls up but the cable pulls on a deactivated lock. It "dry fires" and does nothing.

I'm sure you could still break something but the odds of breaking a handle carrier with my modifications will be reduced 90-95%.

I left the zip tie on figuring no reason to remove.

I was going to just remove the entire lock bar but I'm not sure if it has other functions (lock the key cylinder in) so I just cut off the offending part.

*Re: permanent fix; there's always a chance you could still break a DHC but the majority of unnecessary stress will eliminated with this trick.
Andrew hi, gr8 work , oook so got a new febi bilstein replacement dhc and it has the little tab that you suggest chopping off to alleviate future stress break in the area you cable tied...we sure there are no consequences to dhc open closs process?
__________________
E53 X5 3.0d SUV prod.date 11/2004 eng.variant M57N Europe Right hand drive N
Reply With Quote

Sponsored Links

  #62  
Old 01-26-2021, 03:03 PM
Member
 
Join Date: Mar 2008
Location: CYPRUS
Posts: 2,040
omodos is on a distinguished road
Quote:
Originally Posted by Clockwork View Post
Autoparts way.ca is selling Febi DHC for $71CAD. I just installed mine last night and it's perfect. Comes with new screws too.
Just an FYI.

Sent from my Pixel 3 using Tapatalk
Helloooo did you cut off the tab too?if yes was all still ok afterwards?
__________________
E53 X5 3.0d SUV prod.date 11/2004 eng.variant M57N Europe Right hand drive N
Reply With Quote
  #63  
Old 01-26-2021, 04:14 PM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 12,622
andrewwynn will become famous soon enoughandrewwynn will become famous soon enough
I've been pulling off that whole part on recent repairs. I actually haven't figured out what that part does it looks like an anti-jimmy function.

The primary problem for ice breaking the DHC is actually in the DLA not the DHC so it's possible that part plays no job in the typical break. That said as you can see in one of my videos where the part moves stupidly slow when cold that was the exact sound I heard when operating the door lock with the remote just before I broke mine so it's possible the lock flips it up to prevent your passenger from pulling handle while unlocking
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #64  
Old 01-26-2021, 04:26 PM
Member
 
Join Date: Mar 2008
Location: CYPRUS
Posts: 2,040
omodos is on a distinguished road
Quote:
Originally Posted by andrewwynn View Post
I've been pulling off that whole part on recent repairs. I actually haven't figured out what that part does it looks like an anti-jimmy function.

The primary problem for ice breaking the DHC is actually in the DLA not the DHC so it's possible that part plays no job in the typical break. That said as you can see in one of my videos where the part moves stupidly slow when cold that was the exact sound I heard when operating the door lock with the remote just before I broke mine so it's possible the lock flips it up to prevent your passenger from pulling handle while unlocking
Hmmmm so i guess not to chop off tabs, temps out here don't drop to 0c ever, for that you need to hit the mountains where again i visit maybe once a year si kids enjoy snow,so the temp side of fault wont come into play for me.....i guess cable tie as 'backup' wont do any harm
__________________
E53 X5 3.0d SUV prod.date 11/2004 eng.variant M57N Europe Right hand drive N
Reply With Quote
  #65  
Old 01-27-2021, 02:46 AM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 12,622
andrewwynn will become famous soon enoughandrewwynn will become famous soon enough
They will fail from normal use just fatigue failure unfortunately and I doubt that any difference is achieved from pulling up vs. out. The force that breaks the thing is from the torque applied to the lever/gear, and an argument could be made that when pulling up vs. out it get a more efficient force transfer (true; why it's so much easier to open pulling up), but also that of energy is wasted trying to tip the car over, the force applied to the cable arm hinge is actually less.

I've broken an old DHC during the summer and gently operating the handle. BMW designed the hinge with half the metal around the hinge pins to prevent the pin from getting seized and it turned out to be a design defect because they also used shitty brittle metal because it's easy too fabricate.
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #66  
Old 01-27-2021, 02:54 AM
Member
 
Join Date: Mar 2008
Location: CYPRUS
Posts: 2,040
omodos is on a distinguished road
Quote:
Originally Posted by andrewwynn View Post
They will fail from normal use just fatigue failure unfortunately and I doubt that any difference is achieved from pulling up vs. out. The force that breaks the thing is from the torque applied to the lever/gear, and an argument could be made that when pulling up vs. out it get a more efficient force transfer (true; why it's so much easier to open pulling up), but also that of energy is wasted trying to tip the car over, the force applied to the cable arm hinge is actually less.

I've broken an old DHC during the summer and gently operating the handle. BMW designed the hinge with half the metal around the hinge pins to prevent the pin from getting seized and it turned out to be a design defect because they also used shitty brittle metal because it's easy too fabricate.
ok well either way IF i use a plastic one I dont think it will last the heat out here to be honest, in time it will go brittle -may fall off and cause more damage or a jam you think?
__________________
E53 X5 3.0d SUV prod.date 11/2004 eng.variant M57N Europe Right hand drive N
Reply With Quote
  #67  
Old 01-27-2021, 03:01 AM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 12,622
andrewwynn will become famous soon enoughandrewwynn will become famous soon enough
The DLA freeze only happens in a certain rare set of conditions.

Very humid just above freezing with usually rain but not necessary followed by drop below freezing and enough time.

The door seal will usually freeze requires a lot of force to break open the seal.

Unfortunately the primary way to open the door is also most likely to break the DHC. Pulling on the handle when the DLA is frozen.

You can tell if the DLA is frozen from how the handle feels. If the handle moves far less than usual and has the feeling of bending a spring vs. click of things moving stop immediately.

Gain access from another door and push that door open from inisde.

If the DLA is partly frozen and you luck out and don't break it you will very likey get the latch stuck open. Not much of an improvement.

Once you get a frozen door open you can use a hair dryer into the latch to thaw it out.

The cable arm on the DLA touches the body of the DLA and bring steel they will both "sweat" like a cold soda in a humid location when it's near freezing and lots of humidity.

It takes ONE drop of water to lock the thing solid; watch my video!

Fortunately only takes driving a while to defrost. I've found that 30-40 minute drive has 100% success rate to get the DLA defrosted and no matter the temp it will not re freeze until the same circumstances present themselves
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #68  
Old 01-27-2021, 03:17 AM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 12,622
andrewwynn will become famous soon enoughandrewwynn will become famous soon enough
Quote:
Originally Posted by omodos View Post
ok well either way IF i use a plastic one I dont think it will last the heat out here to be honest, in time it will go brittle -may fall off and cause more damage or a jam you think?


No they can take the heat and I've used nylon a few times before i reengineered with steel. The trade off is you can't get anywhere near as tight so when using as a safety catch, it will be obviously broken when using nylon (but will work) whereas with steel double wrap it's literally much stronger than new and you should never even notice when the hinge breaks
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
  #69  
Old 01-29-2021, 08:25 AM
Member
 
Join Date: Mar 2008
Location: CYPRUS
Posts: 2,040
omodos is on a distinguished road
Quote:
Originally Posted by andrewwynn View Post
No they can take the heat and I've used nylon a few times before i reengineered with steel. The trade off is you can't get anywhere near as tight so when using as a safety catch, it will be obviously broken when using nylon (but will work) whereas with steel double wrap it's literally much stronger than new and you should never even notice when the hinge breaks
okeee this by the way from you is great

https://www.icloud.com/sharedalbum/#...5-4BF5B9F062C9
__________________
E53 X5 3.0d SUV prod.date 11/2004 eng.variant M57N Europe Right hand drive N
Reply With Quote
  #70  
Old 01-29-2021, 08:42 AM
andrewwynn's Avatar
Member
 
Join Date: Jun 2015
Location: Racine, WI
Posts: 12,622
andrewwynn will become famous soon enoughandrewwynn will become famous soon enough
AWR-Fix: Door Handle Carrier Permanent Fix*

Thanks, and I forgot how simple it was to adjust the steel ball for the steel zip tie. And of course I know from experience that the ball will disappear into some crack in the floor if you bend the little finger too far.

The metal zip tie is magically the perfect size and shape to cure this break and since it's steel not pot metal this fix is superior to replacing the part with one made with the same defect as original.

It took many attempts to finally figure out the best way to hold with the vice grip and that's just at important; drops the difficulty from 7-8 to 3-4.

–awr–
__________________
2011 E70 • N55 (me)
2012 E70 • N63 (wife)
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 09:59 PM.
vBulletin, Copyright 2026, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.