hub puller

c4racer · #1 03-08-2010, 06:14 PM

I am in process of replacing a split CV boot (outter). I tried to use an air hammer to free up the axle from the hub, but no dice. I think a hub puller would be a lot more effective. I would rather not remove the axles from the transaxle. So my plan is to swing the hub/knuckle assembly out away from the axle once it is off the axle splines, and then do the boot swap with the axle still installed into the transaxle.

Any suggestions on which hub puller will work on the X5?

Sponsored Links

Repoman · #2 03-08-2010, 08:41 PM

The BMW specific hub puller would be the only one I would use if I were going to use a hub puller since it goes into the bolt holes in the hub. Using a claw puller will dislodge the dustcap which will require more work to remedy. I did not use an air hammer but I did use one hell of a sledge with one hell of a punch. 3-4 good solid blows got it moving expeditiously. This is really the best alternative to the BMW puller. You might want to free up hub/knuckle assembly and check it again, you might have loosened it more than you think. Also, removing the entire axle from the transaxle was VERY easy for me to do and much faster than replacing a boot. I spilled maybe a few drops of transaxle fluid during the swap, not near enough to have to top off. And of course never-sieze the splines of the outer half shaft on reassembly and you won't ever have this problem again. Good luck with it.

mywidebody02 · #3 03-08-2010, 09:39 PM

Quote:

Originally Posted by c4racer

I am in process of replacing a split CV boot (outter). I tried to use an air hammer to free up the axle from the hub, but no dice. I think a hub puller would be a lot more effective. I would rather not remove the axles from the transaxle. So my plan is to swing the hub/knuckle assembly out away from the axle once it is off the axle splines, and then do the boot swap with the axle still installed into the transaxle.

Any suggestions on which hub puller will work on the X5?

did u disconnect the tierod and lower idler arm so the spindle was free to move around? If u did it should have come out. if not it wont have the slack to come out.

djmilleroh · #4 03-08-2010, 09:41 PM

I just repaired my outer cv boot, wheel bearing and wheel hub. I hammered on that hub for hours and had no luck. I would highly recommend removing the hub,bearing everything off the strut and press out the hub and bearing.

Search cv boot diy on the forums if you didnt already there is one out there. If you have trouble finding one let me know.

c4racer · #5 03-09-2010, 12:49 AM

Quote:

Originally Posted by djmilleroh

I just repaired my outer cv boot, wheel bearing and wheel hub. I hammered on that hub for hours and had no luck. I would highly recommend removing the hub,bearing everything off the strut and press out the hub and bearing.

Search cv boot diy on the forums if you didnt already there is one out there. If you have trouble finding one let me know.

I think the idea is to hit the axle, not the hub, right? That is what I was doing. I could try that some more I guess. I have the lower arm off but not the tierod - I guess it would free things up to remove that. Also, I have not unbolted the strut bolts either, so that may have things too tied together.

Repoman · #6 03-09-2010, 03:45 PM

Also, make sure the size of your hammer/punch is up to the task. Remember . . . size matters! I used an 8lb long handled sledge and the equivalent of a railroad tie for a punch.

c4racer · #7 03-09-2010, 05:52 PM

Quote:

Originally Posted by Repoman

Also, make sure the size of your hammer/punch is up to the task. Remember . . . size matters! I used an 8lb long handled sledge and the equivalent of a railroad tie for a punch.

Did Dorothy let you borrow the 7 Dwarfs to hold that log while you hit it?

I have been looking around for a fat punch. Best one I found was a 1/2 thick front to back brass one. I have some beefier ones, but the punch side is on the small side. I wanted to find something with a 3/4" end on it, but could not. I have a 5 or 8 lber myself. I guess worse case I could bring out the 15lber with the really long handle, but it takes two hands to hold it and not sure I want either of my kids holding up a punch while I swing that bad-boy

Repoman · #8 03-09-2010, 06:20 PM

LOL . . . it did seem awkward at first but I put the end of the handle on my hip (pendulum) and one hand close to the business end of the sledge. Other hand was full grip on the punch. I got the punch at Home Depot I think. It's about 8-10" long with one of those rubber handle/hand protectors on it below the receiving end. My buddy was laughing at me until he saw the punch moving about 1/2" per blow. Good times!

c4racer · #9 03-09-2010, 07:45 PM

Quote:

Originally Posted by Repoman

LOL . . . it did seem awkward at first but I put the end of the handle on my hip (pendulum) and one hand close to the business end of the sledge. Other hand was full grip on the punch. I got the punch at Home Depot I think. It's about 8-10" long with one of those rubber handle/hand protectors on it below the receiving end. My buddy was laughing at me until he saw the punch moving about 1/2" per blow. Good times!

NICE!! I will try Home Depot if the brass punch I found today doesn't work. It is 6" long and about 1/2" thick from head to tail.

So did you disconnect the tierod and strut bolts before wacking it? Seems to me you want to hit it before removing everything or the hub ends up just moving with the axle?

Repoman · #10 03-09-2010, 08:35 PM

Quote:

Originally Posted by c4racer

NICE!! I will try Home Depot if the brass punch I found today doesn't work. It is 6" long and about 1/2" thick from head to tail.

So did you disconnect the tierod and strut bolts before wacking it? Seems to me you want to hit it before removing everything or the hub ends up just moving with the axle?

That brass punch might get a pretty good beating. I wacked it before disconnecting the tierod and strut and then once I saw it start to move is when I started disconnecting for removal. I know there is enough play in the cv joints to allow the shaft to move a good bit but don't think there is enough to allow it to come out completely. Oh and also I did douse it with penetrating oil before taking the hammer to it. I don't know if that made a huge difference but it did come out.

The sledge method appears to be a pretty good stress reliever also . . . assuming it comes out of course. Good luck with it and happy wacking!

Sponsored Links