Home Forums Articles How To's FAQ Register
Go Back   Xoutpost.com > BMW SAV Forums > X5 (E53) Forum
Arnott
User Name
Password
Member List Premier Membership Today's Posts New Posts

Xoutpost server transfer and maintenance is occurring....
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management


Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 05-05-2011, 10:09 PM
racemalibu572's Avatar
Member
 
Join Date: Jan 2009
Location: wi.
Posts: 33
racemalibu572 is on a distinguished road
Nikpottala, I'm sorry for any inconvenience this cost you. I had another one notify me a couple months ago about his doing the same thing at 9,000 miles and just thought it was an isolated issue. I have contacted a couple other people I built shafts for and they both have over 25,000 on theirs with no issues. At this point I think I'm going to stop doing the shafts until I figure out what is going on. I'm not sure if it's something with the hardening or if it's the coupler in the case doing the damage. I noticed yours looked rusty again, were the splines greased when assembled and what condition was the seal in. I suppose if someone wants one for a quick fix to get by for a while and take a chance I'll do it but Im currently out of stock on splines right now so it will be at least a week before I get more in if I even order more. If any one else had a problem with my repair please let me know so I can try to figure out what's going on. I have about twenty more out there somewhere. Thanks, Tom.
Reply With Quote
  #2  
Old 05-05-2011, 11:41 PM
Member
 
Join Date: Jan 2007
Location: Oklahoma
Posts: 51
nikpottala is on a distinguished road
Hey Tom,

Thanks for the concern and follow-up. I thought about the hardening of the shaft as well. When I look in the coupler in the case, it doesn't appear to be as worn as the shaft itself so it appears to be related to the shaft material.

When it was assembled the technician and I discussed liberally greasing the splines. Given the close tolerances, I'm not sure how much grease can actually still be in place once assembled. I suspect most of it get's pushed with the end of the shaft and really has little impact.

I'd be happy to send you parts if you want to look them over.

I think the longer shaft is the right idea but I'm not sure what caused premature failure. I just hope the Cobra transmission shafts don't have the same issues since I just ordered from them when I got all the other parts.

This time I did all the work myself so I know exactly what went into the repair. It wasn't all that difficult for a moderate to heavy DYI-type person. I changed the seals and the chain while I was there. Not exactly what I planned to do on Easter Sunday but I'm not as afraid to work on the X5 as I was before.
Reply With Quote
  #3  
Old 05-08-2011, 09:34 PM
bigwave2255's Avatar
Member
 
Join Date: Jun 2010
Location: australia
Posts: 487
bigwave2255 is on a distinguished road
is this unique to pre face lift cars, i have a late 2005 and asked my mechanic to check it out and while the visible part of the spline was rusty he reckoned that there was sufficient contact area but lubed the splines anyway
Reply With Quote
  #4  
Old 05-09-2011, 12:13 AM
Green Dragon's Avatar
Member
 
Join Date: Feb 2011
Location: Utah
Posts: 337
Green Dragon is on a distinguished road
Hey to address the rust issue no matter if you go with Tom's mod or with OEM replacements, send the shaft to Calico Coatings to get the splines micropolished and coated with a composite Teflon that has corrosion/rust inhabiter.

ceramic coatings, teflon coatings, thermal coatings solutions with Calico Coatings


You will never have a problem again. I work for them when I'm home from school and they are an industry leader. Its worth the peace of mind for a hundred or so bucks to have done. Plus they do all kinds of high performance coatings. Their quality is 2nd to none.

The micro-polish makes the splines less abrasive to counter act one eating into the other, and the Teflon coating reduces friction co-efficients and addresses the rust issue. Just smear some Red Line synthetic between the two and bingo.
Reply With Quote
  #5  
Old 05-09-2011, 12:48 AM
JCL's Avatar
JCL JCL is offline
Premier Member
 
Join Date: Mar 2005
Location: Vancouver, Canada
Posts: 11,834
JCL will become famous soon enoughJCL will become famous soon enough
Also to address the rust issue look for the air conditioner condensor drain positioned right above the splines. This is where the moisture comes from that causes the splines to rust. It would be cheaper to reposition the drain than to coat the splines.
__________________
2007 X3 3.0si, 6 MT, Premium, White

Retired:
2008 535i, 6 MT, M Sport, Premium, Space Grey
2003 X5 3.0 Steptronic, Premium, Titanium Silver

2002 325xi 5 MT, Steel Grey
2004 Z4 3.0 Premium, Sport, SMG, Maldives Blue
Reply With Quote
  #6  
Old 07-13-2011, 10:50 AM
ayagutak's Avatar
Member
 
Join Date: Nov 2008
Location: Montreal, Canada
Posts: 128
ayagutak is an unknown quantity at this point
I have this problem transfer case fail, and center driveshaft support, it's expensive what the number and address of that person who can fix this problem,
Reply With Quote
  #7  
Old 07-13-2011, 10:55 AM
Triple X5's Avatar
Member
 
Join Date: Feb 2010
Location: Miami Fl
Posts: 46
Triple X5 is on a distinguished road
Name Tom
Email address [email protected]
Phone #(262) 749-0689


Sent from my iPhone using Tapatalk
Reply With Quote
  #8  
Old 07-16-2011, 07:35 PM
ayagutak's Avatar
Member
 
Join Date: Nov 2008
Location: Montreal, Canada
Posts: 128
ayagutak is an unknown quantity at this point
What r the tools needed for this job, I have to get out the TC and the driveshaft... Do I send the complete driveshaft to racemalibu52
Reply With Quote
  #9  
Old 07-17-2011, 12:15 AM
Member
 
Join Date: Jan 2007
Location: Oklahoma
Posts: 51
nikpottala is on a distinguished road
If you're going to try and go the stop-gap measure and only replace the driveshaft end with a 1-inch longer piece then you only need to remove the front driveshaft. Send the entire driveshaft since the new end will have be be machined and welded to you existing shaft. The stock one comes out with the removal of couple bolts where it bolts on to the front differential. Standard metric socket/wrench set.

If you are going to remove the TC, then you need to remove the exhaust, the front stiffener plate under the engine, the exhaust heat shields and uncouple the rear driveshaft. The only additional special tools for this besides standard socket/wrenches are star sockets for the bolts that hold the TC to the transmission. A 12-point metric end wrench will work on the star nuts for the hard to reach bolts.
Reply With Quote
  #10  
Old 07-17-2011, 04:14 PM
ayagutak's Avatar
Member
 
Join Date: Nov 2008
Location: Montreal, Canada
Posts: 128
ayagutak is an unknown quantity at this point
What the best lasting thing to do, save a on cost and have the problem a few miles down the road or just go with the OEM TC and Drive shaft and be done with it.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





All times are GMT -4. The time now is 07:40 PM.
vBulletin, Copyright 2026, Jelsoft Enterprises Ltd. SEO by vBSEO 3.6.0
© 2017 Xoutpost.com. All rights reserved. Xoutpost.com is a private enthusiast site not associated with BMW AG.
The BMW name, marks, M stripe logo, and Roundel logo as well as X3, X5 and X6 designations used in the pages of this Web Site are the property of BMW AG.
This web site is not sponsored or affiliated in any way with BMW AG or any of its subsidiaries.