|
Xoutpost server transfer and maintenance is occurring.... |
Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Nav gone into default mode how to re-install?
How do you to install the Nav Firmware when the system is in default mode? As the instructions say go into GPS then take the NAV DVD out and then you put the firmware dvd I have got hold of another copy and wanted to confirm: I put the Firmware CD first then turn ignition to first point and the see the on-screen instruction? Or is there a special way? (MKIV DVD based on a X5) |
Sponsored Links | |
|
#2
|
||||
|
||||
Quote:
You say you have a black screen? Did this happen after installing your V26 software? Did the CD pop out on its own or did you have to force it out? From what I understand, when you put the update in, the 1st action is to boot the nav into a specific update mode - from there, the ONLY thing it will do is load an update from a good CD. If this update fails, the CD seems to get stuck in a boot/read/boot cycle (and you have to pfaf about to get the CD out), and when you DO get the disk out, the Nav is 'dead'. Switch on the Ignition to position 1, and insert a known good update disk - if all is well, after about 30 seconds or so, you should see the power light flash and shortly after, the update screen should appear. If it doesn't, the Nav could be stuffed. Hope this helps. |
#3
|
|||
|
|||
I have updated my system many times in past but did a friends today and everything went ok until progress bar stayed at 100% for a few minutes then got "There was an error!" message and now Nav is off line (doesn't appear in menu anymore, fonts larger). Can still eject but won't load the update anymore. Is this terminal or can I recover myself? Luckily still under warranty!
Thanks, Steve |
#4
|
|||
|
|||
Thanks for that. Will give it a go. Luckily the car is under warranty. Could they figure that I tried to improve it?
Had same problem as described by trapdoor and Stevep. Also I noticed a lot of people getting their systems re-coded, why is it that and how would you know it needs to be re-coded? I have v26 already (and installed on my car) very strange it doesn't work in my friends. I am getting hold of v27 and will try that too |
#5
|
||||
|
||||
do you have v26? try putting v26 or some other
version besides the one u just used in.
__________________
|
#6
|
||||
|
||||
Quote:
For me, all the Coding Data has defaulted back to the OEM install - ie. wiped out my VIN, Car Colour and Reg No. and has set back to 7 series as Vehicle Type. I don't have any problems though, but it seems some have issues with buttons on the monitor not working correctly, and things like Aux ventilation etc. disappearing. Check in the Service Mode menu under Telematics (I think) - that will detail the vehicle type, VIN etc. If yours is all there, then you're OK. Gonna get mine recoded next week as its in for an Inspection 1 |
#7
|
|||
|
|||
Is it worth re-installing. Just don't want to put him in trouble for it. He has booked the car in next week for the dealer to fix the problem. Any excuses he can use for the problem he has now (that I caused) with Dealer?
Even though it has gone to default mode - he still has everything (inc Aux Vent, DSP, Code, etc... except Navigation) Stevep have you tried another disc or v27? Let me know please. |
#8
|
||||
|
||||
when i recently upgraded mine to the hacked
v26, i too had issues. i 1st went to v25, then up to v26 hacked. i got the error and all black screen. i re-burned an image at a slower speed, then re-installed and all was good.
__________________
|
#9
|
|||
|
|||
Barflux - The Navigation Computer is no longer recognised in dashboard menu. I can load V27 update CD but the red light doesn't flash or anything load. Is there a way of forcing a reset to load the update again?
Thanx |
#10
|
||||
|
||||
i had same problem .. in MKIII .. last week i update to v.18-2 without any issues then i update to v.23 after finish the system changed to default mode !! every things is shown except Navigation !! i tried to upgrade and downgrade but nothing happen when i put the CD in NAV !! and the light of NAV always Flashing with CD or without !! i try every things and tricks but nothing changed !!
i need your help .. please some one told me the board is damaged and need new one !!! and another one told me just re-coding with dealer . |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|
|