|
|
|
|
||||||||||
| Xoutpost server transfer and maintenance is occurring.... |
| Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
 |
|
|
LinkBack | Thread Tools | Display Modes |
|
#42
11-27-2017, 12:35 PM
|
|||
|
|||
|
It might be here instead
https://www.newtis.info/tisv2/a/en/e...s-rims/OrpQRzM By front left underbody panel 
|
|
#43
11-27-2017, 03:22 PM
|
|||
|
|||
|
That previous link was for receiver... So low cost seems to be the new system past 10/10 mfr date, the one by the muffler.
But our pre 10/10 control unit is under driver wheel.. It's bigger than the low cost one https://www.newtis.info/tisv2/a/en/e...s-rims/P0UXnh4
|
|
#44
11-27-2017, 06:12 PM
|
|||
|
|||
|
If you want to get rid of TPMS and switch to FTM which uses wheel speed sensors, here's what I did today:
I just got it working. Now it says FLAT TIRE MONITOR in CIC! On pre 10/10 build date e70, unplug the RDC module which is under the drivers dash: Follow these directions to get to it... when you unplug and remove it, it will say RDC on it. https://www.newtis.info/tisv2/a/en/e...s-rims/P0UXnh4 On 10/10 and newer build date e70, unplug the RDC module which is located on a frame rail near the muffler: See this link for photos: https://xoutpost.com/1121861-post40.html Or you can see in newtis: https://www.newtis.info/tisv2/a/en/e...-rims/FCVcPPJi Remove VO $2VB from CAS and FRM (not sure if necessary but did it anyway). Things to change in coding modules: Quote: CIC -------- RPA_CIC aktiv RDC nicht_aktiv RDC_SAFETY nicht_aktiv (already off on e70 but check anyway) (For non CIC) CCC RDC_CCC nicht_aktiv MASK and Champ RDC nicht_aktiv EHB (DSC) ------- AUSSTATTUNG_RPA aktiv KOMBI ------- RDC_VERBAUT nicht_aktiv RDC_APPL_MONITOR nicht_aktiv After you do your typical key out, wait a bit, key in start engine. Go into idrive and see the Flat Tire Monitor, you can reset there. That's it! Last edited by robnitro; 11-27-2017 at 07:12 PM.
|
|
#45
11-27-2017, 06:21 PM
|
||||
|
||||
|
Your pre 10/10 TIS link is not valid. Can you confirm complete URL?
Question, do you think this coding could be done in Carly?
__________________
'01 740i Sport MKIV, Quad Brake Lights, Bi-Xenon retrofit, HID Fogs Dinan 7 Struts, Springs, camber plates, Intake, MAF, CAI, Throttle Body, NBT Retrofit, Strong Strut  '99 318ti Titanium Silver; '97 318ti Boston Green; '13 X5 3.5i Saphire Black Metallic '84 633csi Black (sold); '88 325iC Black (sold); '97 740iL Black(sold); '01 740iS Black (sold);'97 318ti White (sold); '08 X5 4.8i Titanium Silver (sold); '96 318ti Alaska Blue (sold)
|
|
#46
11-27-2017, 07:07 PM
|
|||
|
|||
|
Link fixed. No, Carly doesn't have all of the options that NCS offers. Carly is a canned coding approach- much easier to do specific functions but it doesn't give you direct ways to change individual parameters.
Added CCC and mask/champ coding for the flag !DIRECT_RDC (how I found the ones for e70 using that flag) Last edited by robnitro; 11-27-2017 at 07:13 PM.
|
|
#48
12-02-2017, 07:30 PM
|
|||
|
|||
|
Ok. Thanks for all the work. Looked around again today, and definitely not back by the muffler. I'll dig under the drivers wheel this evening, if I get the chance.
|
|
#49
05-04-2018, 08:34 PM
|
|||
|
|||
|
Tpms antenna location for pre 10/10 build date e70
The tpms antenna is right under the driver on pre 10/10 e70's. Remove the panel from under the car and you'll see it right there. Hope that helps somebody!
|
|
#50
10-23-2018, 01:49 PM
|
|||
|
|||
|
TPM RDC repair
If you're reading this thread for the RDC location perhaps this video will help you fix it ... once you find it and remove it.
https://youtu.be/8Vu7GTFcZjU Last edited by YuCrew; 10-23-2018 at 05:32 PM.
|
|
| Bookmarks |
|
|
|
|
Linear Mode
