|
||||||||
| Xoutpost server transfer and maintenance is occurring.... |
| Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
#11
|
|||
|
|||
|
Regards, michael i |
| Sponsored Links | |
|
|
|
|
#12
|
||||
|
||||
|
The cradle will not charge by using the GND and +12v alone mate, it must also have the Cradle_on (from the ULF) connected too.
Do not connect the white to anything other than pin 11 on a ULF (so dont connect to power or gnd), cradle_on is a control wire not a power/gnd wire.
__________________
Sept 03, M3, Silver Grey. Retro-fits: Modded Mk4 DVD Drive, OEM Bluetooth, VR Control, Rainbow Speaker Upgrade, Sony SOT Amp, HK Sub, CCFL, Intravee II, NightMode. |
|
#13
|
|||
|
|||
|
Thank you for your quick reply I just hope that I have not damaged my eject box and cradle by trying the red and brown wires on the cigar lighter connectors. Perhaps when you have time you can let me know.
Being a OAP I will now start saveing up for a retro kit as I am sure you know you can no longer not get the wiring on it's own, so I unable to do what you have done by makeing up my own wiring like you have, unless you would like to make one for me and earn a few bob. I live in Cornwall. Kind regards and thank you. michael i |
|
#14
|
|||
|
|||
|
ccfj1 Is crade_on active high or low? I'm sure with a resistor or two it could be made to charge without a ULF.
|
|
#15
|
||||||
|
||||||
|
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
I know when I was looking at getting it working (without the ULF), it didn't work as I thought it would, and it had some funny charging on/off issues (depending on how it was connected).
__________________
Sept 03, M3, Silver Grey. Retro-fits: Modded Mk4 DVD Drive, OEM Bluetooth, VR Control, Rainbow Speaker Upgrade, Sony SOT Amp, HK Sub, CCFL, Intravee II, NightMode. |
|
#16
|
|||
|
|||
|
Hi John,
Thank you again for replying to me. My car is a July 2004 X3 Sport without being prewired for Bluetooth. What I hope is that you are able to make up the wiring kit for it. I have purchased a Eject Box and Cradle for the center console, at present have Bluetooth via a Nokia CK7W kit and the phone used by me is a Nokia 6310i which I will not replace. BMW Retrofit kit for the car is 84 64 0 306 854. Eject Box fitted is 84 64 0 306 855 and into that is Cradle 84 21 6 930 108 for the Nokia 6310i. What I hope you will be able to do is make up the wiring loom, if it is of help I do have the BMW installation instructions for fitting which also includes the wiring digram with all the connections if it would be of help. I am not able to email them because I can't do things like that so will post it to you if you will give me your address. (PS I did send this email direct to you but hotmail returned it.) As I said to you yesterday the eject box has a 18pin connector (round male pins) with 1 Green Pairing 2 Brown Neg 13 White cradle on and 5 Red 12 volt supply. As you know this information I found on the Xoutpost site. I do not mind if you use second hand parts to fit it may also may be better for you to supply every thing at least you would then be able to test every thing before posting it to me. The main item is the harness made up. Let me know what you wish to do and if you are able to help. Kind regards Michael. Last edited by michael i; 05-06-2012 at 04:05 AM. Reason: incorrect spelling |
|
#17
|
|||||||||
|
|||||||||
|
Quote:
Quote:
Quote:
Quote:
Quote:
It's always a help, but My looms are normally a lot easer than the OEM kit to install, Please send me the install PDF (via PM) and I'll have a look at how it connects. Quote:
Hmmm, I'll PM you my other account. Quote:
Quote:
Quote:
__________________
Sept 03, M3, Silver Grey. Retro-fits: Modded Mk4 DVD Drive, OEM Bluetooth, VR Control, Rainbow Speaker Upgrade, Sony SOT Amp, HK Sub, CCFL, Intravee II, NightMode. |
![]() |
| Bookmarks |
|
|
|
|