|
||||||||
| Xoutpost server transfer and maintenance is occurring.... |
| Xoutpost is currently undergoing a planned server migration.... stay tuned for new developments.... sincerely, the management |
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
|
#1
|
|||
|
|||
|
Quote:
|
|
#2
|
||||
|
||||
|
Great news! Thank-you KiwiJochen!
__________________
E83 - Aero PKG Mods installed: Homelink mirror. CIS-IBUS video module, AUX, Rr Dr Release, stock wheels, Remote start, CarPC (Atom) & mud flaps - NAV - MKIV - NA Map DVD - 2011 E46 - 18.5 wheels/tires (summer), 17 stock (winter), Homelink, NAV software upgrade, BMW video module, Radio to V53, AUX, USB IBUS interface,BMW alarm install, CarPC(Epia), remote starter, tank battery & angel eyes. NAV - MKIII - NA Map CD - High Version 2008.1 |
|
#3
|
|||
|
|||
|
Any luck on the mk3 from Landrover to BMW?
|
|
#4
|
||||
|
||||
|
Hi All,
I will built the Ibus2Serial adapter found with the Navcoder this week-end. I'm preparing all the stuff I need to do this and I've one big question : Inside my 2003 Mini Cooper with Radio boost + Nav Unit (MK3) whitout CD charger, where is the ibus plug ? I've read resler site or HackThe Ibus site and got no answer, only that the MC is ibus compatible ... |
|
#5
|
|||
|
|||
|
workke,
Even if you don't have a CD changer, your MINI should be pre-wired for a CD changer. Look in the boot pocket in the back, there should be a bundled up set of cables. There are two connectors for the CD changer - the one that is smaller, with only 3 or 4 wires in a straight line, is the I-BUS connector. That is the easiest way to tap in to the system. |
|
#6
|
|||
|
|||
|
I have a 2002 '52' plate X5 4.4 and have recently upgraded the nav unit from MKIII to MKIV. I've also just ordered Rolf's interface unit, and have a couple of questions which I would be grateful for some answers to.
Firstly, with regard to accessing the i-Bus, I note that the 3-pin plug at the back of the CD unit is most commonly used. Whilst that is OK, I've noticed a few other unused similar 3-pin plugs on various wiring looms in the area of the CD & Nav units, are all these i-Bus connectors? Secondly, when I upgraded the Nav unit from MKIII to MKIV, I lost the facility whereby a selected destination would have its "Distance" and "Arrival Time" automatically fed across to the Board Computer. Furthermore, when the Nav unit is actively guiding me to a destination, I can't even manually input a "Distance" into the Board Computer, to do this I have to turn guidance off, input the distance, and then turn guidance back on. The Nav unit came from a German X3, and upon searching X5 World for an answer, it may be a simple case of recoding the unit by ticking the Navcoder "Show Arrival Time" box which is applicable to X5s, is this correct as it's both "Distance" and "Arrival Time" that are affected? If this is not the case, I have also learned that software downgrading and re-upgrading may fix the problem, but how (and with what) does one downgrade to an earlier software version? Last edited by Jaycee; 11-20-2007 at 03:20 PM. |
|
#7
|
||||
|
||||
|
Quote:
Quote:
Try coding for your vehicle 1st and see if that works - make one change at a time and then you can post your findings. |
|
#8
|
|||
|
|||
|
Hi am I right in thinking you can use navcoder to proram memory seats to key If so can you tell me how it was done
cheers |
|
#9
|
|||
|
|||
|
Quote:
|
|
#10
|
||||
|
||||
|
Quote:
Or must we go throught OBD2 bus ? |
![]() |
| Bookmarks |
|
|
|
|