Successfully coded my E70

[Mr.X5_3.0si-retired]

Originally Posted by lordshin808

make sure you change all the settings to COM1.

so that all the settings match COM1 in all the ini files.

that and the path i think might be wrong

my path shows by default..
%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\Sy stem32\Wbem;C:\EDIABAS\Bin

that doesn't seem right

my obdi.ini shows for the top portion
[OBD]
Port=Com1
Hardware=STD:OBD

then has UNIT A-D with COM Ports1-4

ediabas.ini has
Interface = STD:OBD

don't remember which other ini i might be missing that needed changing

*EDIT*
didn't realize there was 2 USB drivers for this
a serial port which i knew of already and have set correctly
then a USB Serial Converter so i just went and selected that and manually installed drivers from disc for it

still not sure about my path setting, i know you add ;C:\EDIABAS\Bin to the end which was already there by default
and when i set the one usb driver to com1 it no longer gives me the tab that show to ..

b. Ensure “use fifo buffers” option is marked and receive buffers and transmit buffers are

both set to 8. Once that is finished press ok and exit all windows.
i only see the tab that shows the latency
if my device is not assigned to COM1 then i have the received and transmit buffer options but then no latency?

*EDIT*
last attempt of the night
same error so i thought i'd try FRM option after the F3 part and get a new best version error

not sure what to do now
before i was atleast getting both battery and ignition solid, now i can't even get that??

[lordshin808]

didn't realize there was 2 USB drivers for this
a serial port which i knew of already and have set correctly
then a USB Serial Converter so i just went and selected that and manually installed drivers from disc for it

Oh yea, now that you mentioned it, there are 2 USB drivers to install, I just used the same drivers from the disc for both USB Serial port and USB Serial Converter. So what you did was right.

still not sure about my path setting, i know you add ;C:\EDIABAS\Bin to the end which was already there by default
and when i set the one usb driver to com1 it no longer gives me the tab that show to ..

b. Ensure “use fifo buffers” option is marked and receive buffers and transmit buffers are

[SIZE=3][FONT=Calibri+FPEF]both set to 8. Once that is finished press ok and exit all windows.

I don't think this applies to our cable, because these settings were not available. I only changed it Com1 and Latency to 1.

i only see the tab that shows the latency
if my device is not assigned to COM1 then i have the received and transmit buffer options but then no latency?

*EDIT*
last attempt of the night
same error so i thought i'd try FRM option after the F3 part and get a new best version error

ok, I got the same best version error too. It's hard to remember exactly what I did, because I was going back and forth for several nights with the software and google with all the errors.

Ok, make sure you didn't get any warnings when you ran OBDsetup.exe. I remember I had to change the value in Windows registry to match the expected value. There was one column with my value and then the expected value. I went into the registry path shown on that black DOS screen and changed it match the expected value.

[Mr.X5_3.0si-retired]

just ran obdsetup again
values all match expected side and everything says OK

i may just have to try using an actual windows laptop
just don't know anyone with winXP, everyone has win 7 and i'm not sure if my disc will work on that

[lordshin808]

Originally Posted by Mr.X5_3.0si

just ran obdsetup again
values all match expected side and everything says OK

i may just have to try using an actual windows laptop
just don't know anyone with winXP, everyone has win 7 and i'm not sure if my disc will work on that

Windows 7 32bit works for sure cause that's what i used.

[Mr.X5_3.0si-retired]

Originally Posted by lordshin808

Windows 7 32bit works for sure cause that's what i used.

ok
i'm going to try a different laptop later today and install the disc on it

[lordshin808]

Originally Posted by Mr.X5_3.0si

ok
i'm going to try a different laptop later today and install the disc on it

yea, i really can't think of any else you can try. It's frustrating setting up the software... I know.. It took several nights after work trying to get it all working. i had a bunch of error messages too. At least you only have to do it once. After that, you will have a working laptop to code anytime.

[Mr.X5_3.0si-retired]

Originally Posted by lordshin808

yea, i really can't think of any else you can try. It's frustrating setting up the software... I know.. It took several nights after work trying to get it all working. i had a bunch of error messages too. At least you only have to do it once. After that, you will have a working laptop to code anytime.

haha ya i can't wait for that
i've been running the installs and programs as Admininistrator.. is that fine or it doesn't matter?

[lordshin808]

Originally Posted by Mr.X5_3.0si

haha ya i can't wait for that
i've been running the installs and programs as Admininistrator.. is that fine or it doesn't matter?

administrator is your best bet, rules out permissions issues for sure.

[Mr.X5_3.0si-retired]

ok

i found out the bmw coding tool (newest version) can code apparently but i haven't found a very good DIY for coding with it yet

you use NCSDummy for coding?
i was trying to learn that last night, i kinda understand, i think i just have to try it a few times to get the hang of it

[lordshin808]

Originally Posted by Mr.X5_3.0si

ok

i found out the bmw coding tool (newest version) can code apparently but i haven't found a very good DIY for coding with it yet

you use NCSDummy for coding?
i was trying to learn that last night, i kinda understand, i think i just have to try it a few times to get the hang of it

I didn't even use NCSDummy at all. NCSExpert did everything I needed.

Check out this awesome google spreadsheet I found, it have codes for everything you ever want to code. hahaha, some motivation for you not to give up.

https://docs.google.com/spreadsheet/...CPqY7sEC#gid=0